Search:

Type: Posts; User: S2H

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds; generated 9 minute(s) ago.

  1. Replies
    5
    Views
    797

    well.. bill.... you know me.... so find me a...

    well.. bill....
    you know me....
    so find me a solution....

    2015 4x4 Toyota Tundra with the 5.7.
  2. Replies
    5
    Views
    797

    how do I look at a file with no interface?

    Long time user of HPT... you can probably still find my posts from way back when I was a beta tester and helped develop the software in its infancy
    ....

    I no longer had any desire to work on...
  3. Thread: Rtt?

    by S2H
    Replies
    4
    Views
    3,285

    and its NOT fully Functional.... Seriously... ...

    and its NOT fully Functional....
    Seriously...
    Why teh hell do you release a feature and still have the "2 weeks" bull crap on it...
    either do it complete, or dont release it at all...


    I...
  4. I actually just solved it today.... it appears...

    I actually just solved it today....
    it appears that the wheel speed sensors do not output the correct signal...
    I added a Driveshaft Collar and sensor and ran it straight to the VSS pins 71/72, and...
  5. what setting to make VSS work on 2013 camaro using Front wheel sensor

    What setting in teh ECU need to be set so that I can use the Front wheel sensor for the Speedo


    we have a car with a Transmission swap, and just want the speedo to work
    there is no TCM and there...
  6. Long story short... since there is no real...

    Long story short...
    since there is no real explanation of how the gauge stuff works, I had to just sit down and pluck thru it until I sorted it out myself

    I noticed that in the scanner, the...
  7. 2012 camaro calibrating fuel level for fuel cell??

    can anybody tell me what each value is actually doing???

    meaning...
    what do the primary and secondary volume sender % numbers mean...


    I need to configure it all so that it works with one...
  8. Replies
    18
    Views
    7,035

    might be a good thing to put this in the comments...

    might be a good thing to put this in the comments in the Editor when you mouse over them....
  9. Replies
    18
    Views
    7,035

    So this was the Culprit... stock values are 1.10...

    So this was the Culprit...
    stock values are 1.10 and 0.95

    Raised them both up to 2.0

    plenty of fuel now...
    also, now it calculates the Manifold pressure correctly ...shows the 7-8 psi it...
  10. Replies
    18
    Views
    7,035

    ok... So raising the CylAir WOT Multiplier and...

    ok... So raising the CylAir WOT Multiplier and Cylair Max Multiplier...has helped......

    all I have to say..... is that FORD does some stupid shit in their Tunes......

    seems that it was limiting...
  11. Replies
    18
    Views
    7,035

    how far should I raise them.... and I know...

    how far should I raise them....



    and I know it has enough fuel pump and plenty of injector left...
    its in open loop...no fuel trims... already checked that.
  12. Replies
    18
    Views
    7,035

    new Tune and Log Up... still no change.... ...

    new Tune and Log Up... still no change....

    Tried all the things you just suggested
  13. Replies
    18
    Views
    7,035

    disabled the torque truncation...no change...

    disabled the torque truncation...no change...
  14. Replies
    18
    Views
    7,035

    please actually look at the tune... tell me what...

    please actually look at the tune...
    tell me what I am missing...
  15. Replies
    18
    Views
    7,035

    Ford Raptor Wont Richen up past 3800 rpm

    so I have a Ford Raptor on the Dyno...
    and every thing is decent part throttle...

    when we go WOT, about 3800 RPM (EVERY TIME) the fuel starts to lean out....and I cannot seem to richen it up...
  16. Replies
    6
    Views
    2,799

    2005 Silverado ETC pedal Position shows 155%??

    trying to diagnose a problem....
    ETC Pedal Position shows 155% when I put it to the floor
    TPS(SAE) shows 100% when ETC is only at at 70, and pedal is about half way to the floor

    trying to...
  17. Replies
    3
    Views
    6,645

    actually... they arent banned..... its not a...

    actually... they arent banned.....
    its not a build whatever you want to make the most power challenge....

    its a challenge to build the best based on a set of rules....

    some years its Ford...
  18. Replies
    5
    Views
    4,438

    In USA Vehicles, Lean Cruise is Illegal if you...

    In USA Vehicles, Lean Cruise is Illegal
    if you have a Holden Commodore(Austrailian GTO) it works as they do not have the same emissions laws

    lean cruise works by commanding a leaner than stoic...
  19. yes...procharger... it might have had a diablo...

    yes...procharger...
    it might have had a diablo tune on it at one time...somebody else did the install.... we just did the tuning.

    I'm fairly certain its a wiring issue somewhere, because the guy...
  20. Dodge Challenger goes into limp mode after tune for supercharger

    not sure what I missed...
    but after a tune, this car drives great for about 50 miles, then throws the lightning bolt on the dash...pedal goes limp...thing goes into a safety/limp mode...

    guy...
  21. so help me find where its commanding it from......

    so help me find where its commanding it from...
    cause I dont see it in the stuff I'm looking at...

    and either way.....I've DOUBLED the VE values...and it makes ZERO difference...
    Dyno pull AFR...
  22. it is not a Commanded fuel issue... it commands...

    it is not a Commanded fuel issue...
    it commands the correct amount

    you will have to make a commanded to AFR PID...

    Commanded AFR is Fine....
    I just cant seem to make it add fuel no matter...
  23. Commanded afr is fine. Just cant get actual fuel...

    Commanded afr is fine.
    Just cant get actual fuel to follow
  24. I tried adding the vvt stuff in the eq-ve It...

    I tried adding the vvt stuff in the eq-ve
    It doesn't make any difference..
    The log I posted was with the vvt enabled and with changes in the ve to vvt tables
  25. sorry... I'm not blindly putting in a file... ...

    sorry... I'm not blindly putting in a file...

    what did you change... and why?

    I already see injector stuff is changed...and it does not need to be changed... works fine with MAF...
Results 1 to 25 of 460
Page 1 of 19 1 2 3 4