2011 ctsv auto 6spd
during my log dialing in fueling i noticed every time i jump hard on the throttle i get torque management kicking in pulling timing for clutch control, is this normal? safe to...
Type: Posts; User: ctsv2011
2011 ctsv auto 6spd
during my log dialing in fueling i noticed every time i jump hard on the throttle i get torque management kicking in pulling timing for clutch control, is this normal? safe to...
What information do I need to replace my bricked p59
Do I just grab any green blue connector ecu out the junkyard?
What's steps are needed to get ecu working in my truck never done this before
it is a 2014 silverado gen 5 l83
it chops decent in park or neutral but im forcing it
theres no chop if i put it in gear. i can see the timing stops swinging when i put it in gear, what does predicted tab do under idle>rpm>speed...
here is my log of idle so if i copy paste this into vve and calculate coefficients do you think that will make my idle less jumpy. this is the truck with the maf failed running strictly on speed...
when logging eq err vs map do i log it in kpa or bar?
can someone please explain to me on how to tune my VVE.
is it like gen 4 just log eq error vs map readings copy and multiply by percent into VVE table then calculate coefficients.
if there are...
its not real choppy at all would like to get a steady chop if possible new to gen 5
tuner said thats all the chop that it will do as its not too big but i just thought with a 108 lsa it would chop...
can somebody tell me on how we can make the gen 3 throttle more responsive without bricking the ecu?
haven't messed with this table at all but want the pedal to be more linear. can i just put 3% at...
right but is there a way to say add 20 % accross the board for anything in boost +100 kpa? id rather tune from a car running rich and lean it out then start lean. ive logged for my 1st revision but...
hey guys im trying to add fuel to my VVE table (100+ kpa) so when i go to tune it im not tuning from a car thats dangerously lean while in boost.
i can do this on gen 3 but have never done it on...
Helping out my buddy tune his truck he just bought. We have got it running but doesn't idle the best. I'm no pro tuner I know the basics. Does anybody have a tune for a 5.3 cammed I can compare to...
can someone help explain what to adjust with my tcc settings? looks like my tuner left slip still at 20 rpm.
tune and driving log attached
2011 cadillac ctsv
roughly 650 crank hp
stock...
Did you copzy ZL1 zones and paste into into your zone table? Then just copy vve table from my car to new vve zone map? Just trying to make sure I got this right
i copy table from the log and go to paste by special/multiply by percent, i then click calculate coefficient and this message pops up
(the following zones 17,23,29 are not supported by the data...
Car is running on a MAF only tune right now. trying to learn and understand vve with this gen 4 platform. i failed maf reset fuel trims and disabled stft and logged and this log is what i got. can...
Hey guys, anybody care to share a good trans tune. Have a 01 silverado and trying to get this thing to make solid firm shifts.
or can someone give me some good pointers on what to adjust with mine
anybody willing to share a good layout for logging on gen 3 trucks
added stock timing table back in under 1.00 grams of cyl mass and had a good 30 min drive home with no knock
also jumped on it a little and found car is getting 22.5 degrees on e48. this is about...
will get it unplugged this weekend and disabled related codes for it. ill tune ve against stft this weekend as well.
i added stock timing tables back in today did a quick pull leaving work and saw max of 22.5 degrees on e48 thats about all my pump can handle without the help of a aux pump. i can see the lambda is...
the car was tuned with wideband in the tailpipe. the wideband is now in bank 1 sensor 2 location. b1 s2 is just ziptied up in engine compartment. not sure if wideband changing locations affect it but...
here is some logs. car doesnt do it every single red light but it will do it every drive
Cool man i will send you a email later today once off work, appreciate it
Will give it a shot and post back this evening. Will take a log of the car first for a base point.