Search:

Type: Posts; User: jason k

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    896

    ok thanks for the help

    ok thanks for the help
  2. Replies
    4
    Views
    896

    thanks for the reply is stoich ok during part...

    thanks for the reply
    is stoich ok during part throttle cruise?? most things i read always say 13-14 for part throttle cruise. I am little nervous on this one i built the engine about 80,000...
  3. Replies
    4
    Views
    896

    03 2500 hd questions

    hi i have a small list of questions first off I am tuning my 03 2500 hd truck it has a 6.0, stock bottom, end small cam texas speed 216/220 @.050, 550 lift, 110 lsa, stock small chamber 5.3...
  4. Replies
    8
    Views
    4,329

    i switched my platform option from gmt800 to f...

    i switched my platform option from gmt800 to f body, and swapped over all differences in the calibration from truck to f body, when I swapped a lq4 into my 95 f body. I wired in the ac and...
  5. Replies
    1
    Views
    1,378

    I tried deleting my wideband and then setting...

    I tried deleting my wideband and then setting them up again and now I see what I think is the problem. the Daytona wideband is only listed as an equivalence sensor not an air/fuel ratio is there...
  6. Replies
    1
    Views
    1,378

    afr error w/ wideband

    trying to log arf error for tuning my maf and the scanner won't populate. when I checked to see what I am not logging by hitting control m, it has air fuel ratio sensor highlighted in red. I am...
  7. Replies
    0
    Views
    872

    idle issues with ac on

    hi I have a 6.0 swapped 94 Camaro. I am running a pcm from a 04 express and a cable drive tb. When the ac is on the car idles ok when stopped, but while moving at any speed in neutral it idles...
  8. Replies
    4
    Views
    2,321

    Even tho I previously licensed it ? All I did...

    Even tho I previously licensed it ? All I did was reflash it
  9. Replies
    4
    Views
    2,321

    why do i need to relicense my pcm

    I swapped pcms in my Camaro, which was from a van that I pulled with the engine to one I have already licensed with a vin ive already licensed, then reprogrammed it with my pass thru programmer...
  10. Replies
    0
    Views
    1,255

    operating systyems

    can I program a different operating system into a gen 3 pcm?? I have a pcm service number 12586243 from a 03 express that I want to use in my 95 f body but that pinout has no tach output. can...
  11. Replies
    5
    Views
    3,675

    you can add a speed sensor and reluctor wheel to...

    you can add a speed sensor and reluctor wheel to the 400 I'm running it in my f body on vacation right now so I don't have all the info on what I used but its google searchable I found...
  12. Replies
    3
    Views
    3,135

    Some of the pins are different and the main issue...

    Some of the pins are different and the main issue is there is no tach output from the pcm on the express version and when I installed it I left the pin out the same as a truck configuration I had no...
  13. Replies
    0
    Views
    1,015

    Hardware and service numbers

    hi I have a 95 f body I installed a 6.0 in and was using the pcm from that truck for the swap. I now put that truck back together with that pcm . so I installed a pcm of different service number and...
  14. Replies
    3
    Views
    3,135

    hardware anad service numbers

    hi I have a 95 f body I installed a 6.0 in and was using the pcm from that truck for the swap. I now put that truck back together with that pcm . so I installed a pcm of different service...
  15. Thread: mileage change

    by jason k
    Replies
    0
    Views
    707

    mileage change

    I installed a used cluster in a customers 04 savanna and I reprogrammed it with my pass thru but there is no place to input new mileage anyone have any ideas?? thanks
  16. Replies
    5
    Views
    5,786

    when I click on write entire I get a red ...

    when I click on write entire I get a red BRICKABLE warning should I be scared??
  17. Replies
    5
    Views
    5,786

    all I am trying to do is flash the stock file...

    all I am trying to do is flash the stock file back to the pcm
  18. Replies
    5
    Views
    5,786

    unable to write calibration

    I am trying to flash my truck pcm and get an error message " write calibration selected for (p59) but operating system ID's are different " and it wont write the calibration the pcm...
  19. Replies
    7
    Views
    3,432

    i watched him tune it and looked like a bunch of...

    i watched him tune it and looked like a bunch of copy and paste from other tunes but what really bothered me tho was the massive smoothing of my ve table he did without even running or looking at...
  20. Replies
    7
    Views
    3,432

    put what back to stock? everything? why ...

    put what back to stock? everything? why what is so bad about it the car made 460 to the tire has a decent a/f ratio and runs good obviously I built it and have to warranty it so...
  21. Replies
    7
    Views
    3,432

    why did my tuner do this??

    I built an engine for a customer 383 ls6 with cnc heads, cam, long tubes, etc for a 2004 vette. I got the tune semi close using the tuning school methods I did a VE tune, MAF tune, WOT MAF tune,...
  22. Thread: MAF WOT tuning

    by jason k
    Replies
    4
    Views
    2,285

    or leave it if no starting issues?

    or leave it if no starting issues?
  23. Thread: MAF WOT tuning

    by jason k
    Replies
    4
    Views
    2,285

    thanks next question when doing a ve tune...

    thanks
    next question when doing a ve tune on a stroker with a head and cam change should I copy the main ve table to the cranking ve and scale it down since cranking is a % of main
  24. Thread: MAF WOT tuning

    by jason k
    Replies
    4
    Views
    2,285

    MAF WOT tuning

    when tuning a maf for wot and I get a high error not at wot, when getting ready to make the pull, should I leave that out when copy and pasting into the new tune??6090260903
  25. Replies
    9
    Views
    6,114

    that absolutely sounds like a mechanical problem...

    that absolutely sounds like a mechanical problem inside the unit parking pawl dragging? maybe a snap ring on the output ring gear left out and the splines stripping??
Results 1 to 25 of 142
Page 1 of 6 1 2 3 4