Search:

Type: Posts; User: Proven Power

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    6,187

    i just did this on my windows 8 laptop and its...

    i just did this on my windows 8 laptop and its working great

    go to control panel and device drivers make windows search the disk then it works after that.
  2. Replies
    10
    Views
    8,506

    Why did everyone stop using the LM1 and LM2 by...

    Why did everyone stop using the LM1 and LM2 by innovate motorsport i have the new LM2 with duel sensors and it works fine

    http://www.innovatemotorsports.com/products/lm2.php
  3. Replies
    5
    Views
    3,973

    Bill is this needed for newer GM or is 2.24 fine...

    Bill is this needed for newer GM or is 2.24 fine going to tune tire size and shifts on 2011 GMC Yukon been a while for me
  4. Replies
    1
    Views
    1,793

    lost password

    cant log in and buy credits
  5. Replies
    1
    Views
    1,537

    you need to post a log also so we can see what it...

    you need to post a log also so we can see what it is doing also more info on cam and engine would be nice
  6. Replies
    15
    Views
    7,160

    new heads what to use with lg g5x3 ls 112

    looking at lgs afr 225 mongoose heads anyone have info for me about them engine is 408 bored and stroked ls6:shrug:
  7. Replies
    15
    Views
    7,160

    russ when doing maf tune i would log with maf...

    russ when doing maf tune i would log with maf config you posted and then what do you do just copy and paste or X by percent info on how to do this please thank you
  8. Replies
    15
    Views
    7,160

    Thanks russ i am pullng heads off this weekend...

    Thanks russ i am pullng heads off this weekend due to low compression on many cly. preformed pressure test on low cly with rockers off and can hear air pressure in intake manifold:mad: :mad:
    will...
  9. Replies
    1
    Views
    1,607

    04 gto procharged

    how to make gas pedal not fight you on hard accel
  10. Thread: c5 issue

    by Proven Power
    Replies
    12
    Views
    7,225

    I am tuning g5x3 cam also timing at idle was...

    I am tuning g5x3 cam also timing at idle was frist issue #60 injectors to big will cause problems could not get engine to lean always rich burn your eyes rich went down to #40 injectors and found...
  11. Replies
    15
    Views
    7,160

    russ i have not done compression test yet talked...

    russ i have not done compression test yet talked to vic and found old school tech that built engine ported and polished heads him self :eek: :eek: with out flow bench :eek: :eek: could that be...
  12. Replies
    3
    Views
    2,728

    fixed thanks for replies was short cut...

    fixed thanks for replies was short cut issue:doh: :doh:
  13. Replies
    3
    Views
    2,728

    scaner inop

    I went to use the Scaner this am clicked on icon and it asks for app key i give it and it installs files on my desktop files vehicles vcm scaner.cfg and vcm suite. cfg and i can not get to my...
  14. Replies
    15
    Views
    7,160

    i will check compression this weekend. i have not...

    i will check compression this weekend. i have not been able to drive vehicle since i repaired broken vacuum line at back of intake manifold and found intake gaskets damaged. i guess i should expect...
  15. Replies
    15
    Views
    7,160

    still stalling when put into reverse. cant get...

    still stalling when put into reverse. cant get out of drive way. hear is log from cofig you posted. just setting in drive way you can see when it stalls out and i restart i have to hold throttle and...
  16. Replies
    15
    Views
    7,160

    log from a few min. ago using idle config frist...

    log from a few min. ago using idle config frist and normal config afterwards engine stalling will not idle unless i hold to 1200 rpm with pedal
  17. Replies
    15
    Views
    7,160

    is this better

    is this better
  18. Replies
    15
    Views
    7,160

    42# green tops what would be good timing and...

    42# green tops
    what would be good timing

    and can not find these tables
    idle RPM & Map of the engine.

    thanks alot for the help russ k
  19. Replies
    15
    Views
    7,160

    ohno idle tunning

    :shrug: :shrug: this is log from russ idle log config need some help never tuned g5x3 cams and engine was built by some other shop also tune all stock but injector flow and timing 99 vette was told...
  20. thanks russ how would i do the maf tune and i...

    thanks russ how would i do the maf tune and i will put ve tables back to stock for now and get windband ordered:doh: :doh:
  21. this vehicle has bbk 80mm intake and throttle...

    this vehicle has bbk 80mm intake and throttle body has anyone had problems with i have vacuum leak i think is plate at bottom of intake
  22. Replies
    6
    Views
    3,493

    that is cofig file you need to scan and save data...

    that is cofig file you need to scan and save data as over towards middle of screen you will need to scan and stop scan and then save data as will work then looks like save config but is save data as
  23. Replies
    6
    Views
    3,493

    start with timing in idle also post log at start...

    start with timing in idle also post log at start up this will show every body what it is doing at start and when it stalls
  24. injectors replaced and intake gaskets replaced

    hear is new cold start log stalls out if you rev up and let idle down log is cold start to hot very long stalled about five times cold and hot
  25. thanks fixed roof found out injectorss are used...

    thanks fixed roof found out injectorss are used one could be hanging open ????
    ordered 42# green tops today need to start somewhere and that is a problem for sure runs rich all the time just can...
Results 1 to 25 of 65
Page 1 of 3 1 2 3