Search:

Type: Posts; User: AbsolvedJD

Search: Search took 0.00 seconds.

  1. Replies
    21
    Views
    20,596

    After hours of searching I finally find this...

    After hours of searching I finally find this thread with jakebdb56's 2 bar boost function string. It worked like magic after hours of trying to get a boost reading on the scanner. It all started when...
  2. Lean decel and tip in knock on a Procharged LS1

    2001 WS6 P1SC with 228/236 112 cam. Mods in sig. Tune, config, and logs attached. Tuning with HPtuners Pro and LC1 wideband, SD tune.

    I’m getting a very lean decel condition after WOT and part...
  3. Replies
    3
    Views
    2,589

    Also, do I put the gas tables back to 10 when I'm...

    Also, do I put the gas tables back to 10 when I'm back in closed loop? I know the other tables absolutely have to go back to their previous values in order for CL to function...

    And I've done some...
  4. Replies
    3
    Views
    2,589

    Thanks man. I know my start up airflow is...

    Thanks man.

    I know my start up airflow is totally funky but it starts like stock every time. It stumbles with any changes made to it.
  5. My 06 GTO did the same thing except for the...

    My 06 GTO did the same thing except for the asking me to purchase a license part. It happened after a successful tune. It said contact dealer, wouldn't start, and hptuners editor couldn't locate VCM....
  6. Replies
    3
    Views
    2,589

    Quick LS2 OLSD tuning setup question...

    "Open Loop EQ Ratio Gas (Gear): This table is used to determine the commanded open loop equivalence ratio when running on gasoline and the transmission is in gear.
    Open Loop EQ Ratio Gas (P/N):...
  7. LC1 installed and working. Histograms set up and...

    LC1 installed and working. Histograms set up and working properly. TIME TO TUNE! But 10.8 at WOT? And 13.5 at idle? Set at 1/12th timing, which produced the most consistent numbers. Logs to come soon.
  8. Latest tune attached. Fattened the VE in the...

    Latest tune attached. Fattened the VE in the problem areas and smoothed it. A little better...
  9. My thoughts exactly. I've gotten most of the...

    My thoughts exactly.

    I've gotten most of the bucking tamed by tuning my VE table using fuel trims as instructed in the LS2 guide on here. Most improvements came from reducing timing in the...
  10. I'll try those fail numbers to see what happens...

    I'll try those fail numbers to see what happens but the ls2 guide on here says to put both numbers to zero?

    And should I just "smooth selection" on the whole VE table?

    Also, I'm gonna tune...
  11. It shows tunes and logs posted on my screen. I...

    It shows tunes and logs posted on my screen. I disabled it by setting both fail numbers to zero.
  12. DFCO and CFCO are disabled...

    DFCO and CFCO are disabled...
  13. Should I be registering MAF numbers on my scanner...

    Should I be registering MAF numbers on my scanner if the MAf is failed by setting both numbers to zero? MAF is still plugged in.
  14. Haha. It's cool. It would probably be easier to...

    Haha. It's cool. It would probably be easier to tune the idle if it was set up that way!
  15. Thanks for replying Bill. I've read many of your...

    Thanks for replying Bill. I've read many of your posts, including the one you mention. They are always very informative! I will do your idle tuning procedure in the next few days to see how far off I...
  16. LS2 GTO...Opinions on my min RAF changes and other ?s

    When I got my 06 M6 LS2 GTO back from the speed shop that dyno-tuned it I noticed I had idle problems not there before I took it in. This was not my first cam or tune from them (I installed all...
Results 1 to 16 of 16