One of the forum members, GTPprix sells new C6 ECM's for a very good price (I bought one myself as a spare) which is set up to your VIN. So if you have no luck getting your original ecm unlocked, a...
Type: Posts; User: siffert
One of the forum members, GTPprix sells new C6 ECM's for a very good price (I bought one myself as a spare) which is set up to your VIN. So if you have no luck getting your original ecm unlocked, a...
Thank you.:cheers:
What are you saying Russ in reply #4? What does zeroing out the AC Torque Reduction table do in terms of TM? Thanks.
:shrug: What can I say? Off to download 2.2.2 Thanks! :cheers:
I think he is saying to try official 2.2.2 version, not the beta.
I had the same "Not ready - ECT Low" message as 8850 in my 2007 LS2 A6
Corvette that I tried today. I followed the instructions above completely.
Using V2.2.0 Its not the car, its a problem with...
I triied it with my '07 LS2 A6 Corvette using 2.2.0 and could not get past #7 "begin" (nothing to click) either. Got the "Not ready - ETC Low" message just below it, just like 8850 got too.
...
Thank you. Member 8850 tried it with the latest HP beta today with his 2008 LS3 and it was a no go. He was using this procedure by Vette Doc:
...
He just tried it not more than a half hour ago. I'll get on him to report it.
Going to try it on my 2007 LS2 tomorrow.
Member 8850 just tried it on his 2008 Corvette LS3 using your latest beta and no workee.
Does this Hp Scanner relearn procedure work with the E38 ECM for my '07 Corvette?
Thank You. Let me know when they come in.
btw-what is a "your vehicle will require a Crankshaft Position Variation relearn" procedure"?
Is this something somebody who does not know the inner...
I noticed your signature and went on your website. You got a "new oem E38 ECM" for my 2007 Corvette for the price listed?
It was on CF and started by a Tech. See First Post Page 1 and First Post Page 3
http://forums.corvetteforum.com/c6-corvette-general-discussion/2253231-warranty-and-aftermarket-tunes.html
I read this from a Tech on a Corvette Forum regarding the E-38 ecm that is in my 2007 Corvette.
"The ECM firmware contains a counter which tracks how many times it has been flashed. Unless there...
The question is...does replacing your HPT modified tune with your oem stock tune constitute a non-GM calibration or a GM A-OK calibration? Does anyone have a Tech 2 to prove this out? ie: take your...
I am under the understanding that if you tuned your ECM (after saving the oem stock tune) and then reloading your original stock tune, there is nothing that GM could notice about that to "change GM's...
I dont think the original guy I quoted in the first post had the same problem
you are taking about. But I now see what you were talking about with
"toasted ecm's". So a toast and :cheers: to you! ;)
Thanks for clearing that up. I also read elsewhere :secret: that there is a software fault in the current TIS system used by someone this week, and not due from GM or the dealers locking the ecm....
Thanks much for the explanation of my #1 question! I also found out TIS stands for Techline Information System. Though at this time I am worried about going to the dealer for an updated calibration...
Hi...could you please explain in newbie tuner words just what:
1. TIS means
2. typically TIS cannot rewrite the seed/key or other protected areas
means.
??? We are not talking toast here. That guy's ECM was not toast and claimed it ran fine when he left the dealer, he just could not open it with his Diablo.
That is some nasty knock and a nasty trick by the gas dealer! I would put sugar in that fake 93 dealers tank if I could :D Though I would not recommend anymore WOT 60-100 runs on 87 in the future!;)...
I just read about this-see below.
Has anyone heard about dealers now reflashing your PCM and with locking it?
...
Thanks for the prompt reply, in the future I will save to .hpl and then export to .csv.