Alright, it looks like I am now scanning for the Boost. However, it looks to be pulling data in Kpa not psi. If it is pulling correctly and I am converting correctly, I'm running way more boost than...
Type: Posts; User: JAXFL_SS
Alright, it looks like I am now scanning for the Boost. However, it looks to be pulling data in Kpa not psi. If it is pulling correctly and I am converting correctly, I'm running way more boost than...
First off, long time lurker, but haven't posted in quite a while. I have an 08 HHR SS that has been tuned via HPTuners for over 2 years. However, it was tuned by me and a buddy using some basic...
I have been working to try to calibrate my MAF with my intake. I think I am almost there, though I have trouble getting consist numbers on scans. However, what concerns me is that I seem to have...
Breadfan and I were talking and I/we were wondering if it will hurt anything to leave the MAF Base at 1's in the tune? I have my MAF calibrations pretty close to zero in the scanner each run, but...
Thanks cbssob! I checked out your vid on KR and I think it explains everything. You the man!
Thanks Breadfan. I'll try taking what I have and throwing it in the MAF base to even things out. My run this evening still has some high numbers, but they have shifted cells to the higher ranges.
...
So, I have been working all week to even out my MAF. I am getting pretty close in the majority, but I still have some high spots in the mid - upper ranges that I can't seem to get down. Also, I seem...
Any work done based on that LLY config you posted BostedLT5? I am going to start working on my 05 4x4 after I finish working on the SS and would love a good config file to start from...
Nevermind. I found it. Had to change my View.
Still learning...
In watching some of CobaltSSOverBooster's LNF tuning vids, I have noticed that I don't seem to have all the same tables. One major one missing for me is the Desired Air Load table. I have the 2.23...
So when we are watching for it to get closer to 0, that is in the scanner, not the editor?
yeah, it is set on Average. I took the scan from this morning and updated the parameters in the Editor via paste special %. I uploaded those to the car, drove around, and scanned again. When I now...
I think its just something in the copy paste special procedure is hinky for me. Something in the tune is jacked and causing the flutter issues. After reloading the base tune last night and even after...
It is full intake, but according to ZZP should have been direct replacement. No MAF swap needed.
ok. I wrote calibration back to stock after my latest run failed. I wasn't sure it that was getting everything back or not. guess it did.
I went back to the base file and changed the MAF Base...
thanks guys. i appreciate the insight. I'm starting to see why people pay you gurus to write the stuff for us (I'm going to forge ahead on my own cuz I'm stubborn I think)
I watched the vid a...
yeah, completely different. I wonder why? could it be something in 2.23 beta i'm using that is causing the paste to be different?
noob question. can I utilize the file you attached. load it into...
well that failed too. wrote the attached hpt to the car. the attached log is after writing it and going for a spin. P0101 code. turbo shutdown.
back to base tune. I will await your replies.
...
I think everything as far as the trims was pretty good until I installed this ZZP intake. Ever since, I get IAT and MAF (P0101) codes that I have to reset. I have checked everything as far as...
Alright. Let's try this again (I couldn't get the attachments to load earlier).
The config file is the one from Post #1 of this thread.
The hpl is the first log I made after setting everything...
Been following the thread steps to the "T". However, on my 3rd rendition, I am getting some major turbo flutter and then it throws a MAF code and shuts down the turbo.
Me thinks this isn't how it...
I'm very new to this so please forgive me. I am trying to follow this thread and also the original BYT thread, but I am not getting very far. In the original post, you had a sample config file to use...
I am very new to HPTuners (2nd post I think). I have been perusing the boards and trying to gain as much knowledge as possible about my platform. I haven't yet purchased the suite, so I am sure...
Dan here in Jacksonville, FL. Been on ChevyHHR.net since I bought the SS in July 08. Just getting into the tuning phase as I have added a number of bolt-ons recently. Very interested in learning...