Search:

Type: Posts; User: Brians6

Search: Search took 0.00 seconds; generated 12 minute(s) ago.

  1. Replies
    10
    Views
    6,196

    Bump for getting this feature added

    Bump for getting this feature added
  2. Replies
    17
    Views
    14,136

    Im having the same problem, worked before but...

    Im having the same problem, worked before but today my MIL light came on and the thing wont bring up any codes, its not saying " No DTC's Detected" like it usually does which leads me to believe its...
  3. Replies
    8
    Views
    4,450

    I'm on your level man. It's starting to make...

    I'm on your level man. It's starting to make sense though just keep reading especially in the forums if you have a specific question about something chances are so did someone else and there's a...
  4. Thread: Wideband

    by Brians6
    Replies
    0
    Views
    1,277

    Wideband

    How are you all routing the harness? Specifically for a GTO but any other examples are welcome.
  5. Thread: Won't Idle

    by Brians6
    Replies
    3
    Views
    1,892

    Whats confusing me is the copy paste special...

    Whats confusing me is the copy paste special function. I understand how it works (i think) and i dont see why i would want to paste special multiply % to the MAF Airflow vs Output Frequency from the...
  6. Thread: Won't Idle

    by Brians6
    Replies
    3
    Views
    1,892

    Just doing part throttle until the wideband gets...

    Just doing part throttle until the wideband gets here, which should be today.
  7. Thread: Won't Idle

    by Brians6
    Replies
    3
    Views
    1,892

    Won't Idle

    Dont know why, i took a log (posted below) using this same tune and it was fine. Copied and pasted special multiply % half low and hi maf tables and now she wont idle. I cant figure out why.
  8. Thread: Histogram Help

    by Brians6
    Replies
    2
    Views
    2,151

    Ok, yeah im an idiot

    Ok, yeah im an idiot
  9. Thread: Histogram Help

    by Brians6
    Replies
    2
    Views
    2,151

    Histogram Help

    Trying to dial in the maf, i took a log and saved it to come back to later. However when i opened the log file again the histogram file was not populated anymore and i was wondering if there is a way...
  10. Thread: Smog Failed CA

    by Brians6
    Replies
    2
    Views
    1,846

    Smog Failed CA

    Idle emissions failed, smog tech said the it was running rich and Im not really sure why. The car was in open loop and and it looked like it was going to pass so went ahead and ran the test but then...
  11. Replies
    13
    Views
    7,523

    +1

    +1
  12. Thread: High STFT

    by Brians6
    Replies
    4
    Views
    2,805

    Ok, turned it on and let it idle for awhile, the...

    Ok, turned it on and let it idle for awhile, the stft seemed to level after a bit. Ran like crap for the first few minutes though.
  13. Thread: High STFT

    by Brians6
    Replies
    4
    Views
    2,805

    Here's a log i took immediately before turning...

    Here's a log i took immediately before turning the light off,
  14. Thread: High STFT

    by Brians6
    Replies
    4
    Views
    2,805

    High STFT

    Took this log after turning SES light off, for the following codes

    [ECM] P0174 - Fuel Trim System Lean Bank 2 (SES) (Old) (History) (Immature)

    STFT B2 gets near 40% after frame 1049 and then i...
  15. Replies
    17
    Views
    8,093

    Did that last night and thats when i got the...

    Did that last night and thats when i got the irradicate LTFT's however i just took another log this morning on my way to school and they seem to be getting better, i guess it just takes awhile for...
  16. Replies
    17
    Views
    8,093

    So, if you reset the fuel trims once you allow it...

    So, if you reset the fuel trims once you allow it to go back into CL what happens? I ask because when i did this my LTFTs were all over the place and im not sure if they were like that before as i...
  17. Replies
    17
    Views
    8,093

    I know this threads old but, what do you mean by...

    I know this threads old but, what do you mean by clearing out the fuel trims after disabling CL? Do you mean in the scanner?
  18. Sticky: I think what they are saying is that, "it should...

    I think what they are saying is that, "it should be okay, but do it at your own risk."
Results 1 to 18 of 18