Search:

Type: Posts; User: K-fed

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    997

    I was in the same boat and ended up using a...

    I was in the same boat and ended up using a Vintage Air standalone PWM kit. Just have to tap in a separate temperature sensor. Works well. Only part I didn't like is for the A/C it's an override...
  2. Replies
    2
    Views
    889

    TPS needs reset. It's showing voltage at idle. ...

    TPS needs reset. It's showing voltage at idle. I don't see an IAC count. Need to log that on a DBC system.
  3. Thread: mismatched ecm

    by K-fed
    Replies
    10
    Views
    2,937

    Both for the same exact vehicle and operating...

    Both for the same exact vehicle and operating systems.
  4. Thread: mismatched ecm

    by K-fed
    Replies
    10
    Views
    2,937

    No. ECM and TCM must match

    No. ECM and TCM must match
  5. Thread: Gen4 needs a pro

    by K-fed
    Replies
    4
    Views
    1,611

    Looks very rich and could use a little more idle...

    Looks very rich and could use a little more idle timing to get you started.
  6. Replies
    8
    Views
    1,758

    Those codes are useless in a swap. I see some...

    Those codes are useless in a swap. I see some are still active. Uncheck those codes and set to "No Error Reported"
  7. Replies
    8
    Views
    1,758

    There's the log files but still need the tune...

    There's the log files but still need the tune file. Add it in attachments
  8. Replies
    8
    Views
    1,758

    Post your log and tune file for better help

    Post your log and tune file for better help
  9. Replies
    2
    Views
    831

    Did you repoll for supported parameters?

    Did you repoll for supported parameters?
  10. Replies
    6
    Views
    1,193

    Your speed shoots up to 158mph. Definitely a...

    Your speed shoots up to 158mph. Definitely a communication error. Double check all your wiring
  11. Replies
    12
    Views
    3,246

    Fuel pressure is set to 72psi? Also make sure...

    Fuel pressure is set to 72psi? Also make sure the wires your pulling power from on the 67' to the standalone harness have constant power to them after cranking. I had a friend with a pickup that...
  12. Replies
    12
    Views
    3,246

    Did you disable starter and clutch tables

    Did you disable starter and clutch tables
  13. Thread: 8l90e swap

    by K-fed
    Replies
    15
    Views
    3,836

    Any updates on this? Shouldn't the codes for...

    Any updates on this? Shouldn't the codes for u0140 no com with bcm and u0121 for ebcm be set to "no error reported" since you don't have them anymore? The same goes for your rear O2's, evap, etc...
  14. Replies
    8
    Views
    1,321

    I agree, not a lot of info here and I'm not sure...

    I agree, not a lot of info here and I'm not sure what's going on either. Were these both the same harnesses and ECU's? I do see under the OS tab your TCS patch etc are not applied in one tune and...
  15. Replies
    8
    Views
    1,953

    Delete your Starter Fault Checks as well under OS...

    Delete your Starter Fault Checks as well under OS and Theft deterrent codes under DTC's. That should get you running. And your rear O2's assuming theres no cats since cat overtemp is disabled. ...
  16. Thread: 8l90e swap

    by K-fed
    Replies
    15
    Views
    3,836

    I just noticed in your log you have 2 current...

    I just noticed in your log you have 2 current trans gear that read different. One looks like its shifting but way fast for the speed. The other in 3rd gear like you said. Like Cadillactech said...
  17. Replies
    4
    Views
    1,083

    I appreciate your knowledge on the subject Shrek....

    I appreciate your knowledge on the subject Shrek. Can you enlighten me on the troubles with these transmissions besides not having the right rear gears can cause lots of problems with these? I'm...
  18. Thread: 8l90e swap

    by K-fed
    Replies
    15
    Views
    3,836

    What rearend ratio do you have in the car? The...

    What rearend ratio do you have in the car? The current gear shifts way too soon if thats right. I know the 8 and 10 speeds don't like crazy gear ratios and don't shift right.
  19. Replies
    4
    Views
    1,083

    I'm new to the Gen 5's for standalone operation. ...

    I'm new to the Gen 5's for standalone operation. This is an L86 with the 10 speed auto. I thought that might be the best route would be using the same OS and ECM TCM as what it came with. Am I...
  20. Replies
    4
    Views
    1,083

    E92 Write Service Needed

    Is anyone here able to help me out and flash a couple ECU's for a VIN write service for me on a few e92 junkyard ECU's I have for say a 2019 Yukon? Going to use them for a few standalone projects....
  21. Replies
    29
    Views
    4,901

    I was in the same boat as you with the GMPP e67...

    I was in the same boat as you with the GMPP e67 ECU and the EZ-TCU controller. Didn?t like the transmission controller so I just purchased the GMPP transmission controller for my 4l80e. It did need...
  22. Thread: LS427/570 tuning

    by K-fed
    Replies
    5
    Views
    1,744

    You can tune them and make changes just fine....

    You can tune them and make changes just fine. They just don?t have certain features like PWM fans etc like factory ECM?s would.
  23. Replies
    10
    Views
    2,411

    Just wanted to update this... Looks like my...

    Just wanted to update this... Looks like my options are get a standalone PWM fan controller, which won't let run the A/C settings from the ecu so that means fan is on full speed when the A/C is on,...
  24. Replies
    10
    Views
    2,411

    Thanks for the reply. I should see if I can get...

    Thanks for the reply. I should see if I can get ahold of them.

    I just transferred the important tables over and fired it up and went for a quick drive last night. Speedometer was WAY off as I...
  25. Replies
    17
    Views
    3,007

    After you adjust the set screw for your throttle...

    After you adjust the set screw for your throttle body blade, you have to do a tps reset
Results 1 to 25 of 44
Page 1 of 2 1 2