Search:

I had found it in the past, but can't find it now by searching. There was a picture somewhere that was a screen shot of the Main spark advance table, and they zoned it off to show; Idle, cruising,...

I know this is old, but was doing some research to set up the scanner to check my maf.

Im using the NGK AFX also, but I was looking at your PID for afr error and the thing that doesn't make sense...

With the hours it took to make this please allow to be worth of sticky threat material :D

You can use this data collected by selecting groups of cells that are way off (I usually pick them all together if they are more than 1.5 off) and copy and special paste into the same ve cells in the...

So now the config needs to be set up so you have everything you need, but don’t waste bits of data through the cable…if you have to much you don’t get as good of resolution.
...

Now I’ll briefly go through setting it up in hptuners. Its been awhile so I hope I remember how I did this, and I show it right.
BEFORE using the data collected to tune your ve table make sure you...

Now I didn’t leave much room from the relay to the end of the plug, so I couldn’t mount the controller to far away from where it came out from under the center consul, so I just stuck it in the cup...

Alright, now for the inside of the car. I took and left out as much wire as I need to put the controller where I wanted, and I took the extra wire and wound it up and used a twisty tie to hold it...

To plug the hole I had created, it was kind of a trick. I had a guy at ace hardware suggest a stopper…then he was like “oh yeah, need to run the plug and wires through it” we thought for a while on...

Now for the hole, I had to remove the center consul. I believe there were two bolts facing sideways up under the dash by the floor, pull the change holder out, there were some under that, Need to...

Now this is the path starting from the fuse area that I ran the wire. I started with the bundle down at the bottom and got a long metal fire stirring rod that had an L-bend at the one end, had my...

Alright, I’m doing this write up because when I first bought my wideband I was looking like crazy to get ideas on how and where to run the wires to set this up for a street car. I wanted to have it...

If you have hptuners there is a picture if you go into help that shows what each is. You can always google it in the images, that is what I had to do once when I didn't have my laptop.

guess the config and histogram file would be helpful to get advice

This is all done on a 99 ls1 ta

Alright so I set up my scanner config to log the lambda and lambda error (in the histogram too) in order to start tuning my VE table. At first I had to adjust my...

Do you have any recommendations on a relay to use?

I was thinking about something along the lines of a Cubed 12vdc 15A relay.

Alright so I've been reading around here for awhile, can't really play with my hptuners to much (darn snow).

I still need to get my NGK AFX installed into the car, but I've been working on...

Starting this thread to have people post anything useful or interesting that they have found while using HPT that may be helpful for newbies or even the season user.

I know there are things that...

hah, i checked my email on my phone and read the last part...needless to say I didnt smack myself in the head, but after reading I thought to myself 'son of a .... " and felt like an idiot.

Glad...

I know this is digging up an old thread but I got ?'s about wiring it up.

I think I have have everything down, but wanted to double check.

now I understand where there wires go to the hpt...

At first I wasn't really sure.

I'm still new at this so I was trying to see what I could figure out with just the data I had collected so far. From what I could tell is my ltft were high ( I...

New to hptuners and just did a log while we drove from one town to another then went driving around delivering things ...then hit a speedbump and tore part of my exhaust off so the tunning logging...

Just got hptuners, and was wondering how to get the version before the latest one (the beta) to work.

Say I need framework 2.0, which I cannot get to work with windows 7.

Didnt want to use the...