Does anyone have a stock 07 Ram 5.7 hemi tune file? Need one ASAP.
Type: Posts; User: umbrae
Does anyone have a stock 07 Ram 5.7 hemi tune file? Need one ASAP.
After a calibration flash on a 07 Charger RT, it will no longer start. Throwing U0100 code, and says no communication with PCM. It flashed the computer without issue, and I have flashed it several...
I appreciate the feedback, always looking to improve my tuning. I had a SS LNF car 4 years ago, and havent done much with them since. This tune was from last year, I know things have come a long way...
Thanks, much appreciated.
Looking for some feed back on this tune in a lnf Cobalt. GM 3 bar map sensors, maf relocate, intake, catless downpipe, intercooler and pipes with external bov and S20g. Datalog from a dyno pull and...
Start the car, push and hold the traction button till the trac and esc is off, make a pull and 5000rpm every time. I can post my tune file if someone would like to look at it. I've tuned several of...
Is this a garrunteed solution? Never heard of that before. Thanks for the help. There must be a limiting table that isn't accessable yet?
Yes I have traction and stabilitrac shut off.
Can anyone offer some insight as to why im hitting rev limiter at 5000rpm while on the dyno? I've never heard of this and could not find anything regarding this situation. 08 Cobalt SS TC. All of my...
sent you a PM
Can someone help me out with injector data for SVO 30lb injectors. Im tuning a 2002 LS1 ECM in a 96 Z28 with EFI Connection 24x Conversion.
I have purchased the Greg Banish DVD, but it arrived...
96 Z28 with LT4 crate motor, EFI Connections coil conversion with 2002 PCM.
I can read the ECM but I cannot write to it. Mode-1 Failed while trying to erase ECM. I've attached the file. Need to...
This was correct... there was a problem in the harness, and has been resolved, thanks everyone!
enabled them and reloaded the tune, no change, so I swapped in a good working O2 and still no change. thanks for the quick reply tho.
Hooked the scanner up to the car today and 02's are stuck at .450 and there are no fuel trim readings?
Just finished a heads and cam swap on 99 LS1 motor. Grounds are all connected, everything is...
2008 Pontiac Torrent GXP, will not read the VCM. Error message is VCM read failed at loc: 2000 error: timed out. Anyone have any suggestions? The vehicle is like brand new, fully charged computer,...
I've tried everything in this thread, and I cannot get it to run. Says cfg file is corrupt. I've installed the drivers without issue, just cant get the program to open. HELP ANYONE?
does this actually take a month?
I got it to read, then HPtuners locked up on me before I was able to save the bin. I havent had time to try since then. Maybe tomorrow. Thanks tho Bill.
Keeps timing out.. this time loc 4800. Sometimes it wont connect at all.
You would think that I have never used this program before... ha!
I have the ability to scan, but I can not get it to upload the stock file. I got an error, loc 3400 , and now I cant even get it...
If any one else has this problem, its the cigarette lighter fuse.
I dont have power at my diagnostics port? Which fuse in the panel controls that? I check the manual, but it doesnt list anything specifically. 2004 Sierra 2500HD
Im sitting in the truck on the...
I would hate to desensitize the knock sensor if in fact its real knock. If I desensitize the sensor by 25% (for example) and I still get the same amount of knock, would that mean that its real knock?
Can someone have a look at this log. Its a stock Sonoma with a ton of knock. It has new plugs, wires, distributor, air filter. Im not sure whats up with it? Where should I look? He said it was down...