Search:

Type: Posts; User: blown 04

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,748

    Cylinder charge temp bias table.

    Cylinder charge temp bias table.
  2. Replies
    1
    Views
    1,212

    im going to lower my tps value to 35 . has...

    im going to lower my tps value to 35 . has anybody seen where there are time pe don't work? im going to try my buddies x link just to eliminate that.
    ?
  3. Replies
    1
    Views
    1,212

    power enrichment issues please help

    looking over some logs trying to solve a lean spike on throttle transitions I found a few times where the map and throttle values were reached but the commanded never changed from stoich. but other...
  4. Replies
    9
    Views
    4,353

    .048 I meant

    .048 I meant
  5. Replies
    9
    Views
    4,353

    0.48 x 31.124308 = 1.49

    0.48 x 31.124308 = 1.49
  6. Replies
    9
    Views
    4,353

    Is that 1.5 what you see at idle or on...

    Is that 1.5 what you see at idle or on deaceleration?
  7. Replies
    9
    Views
    4,353

    so this can help with a lean tip in? im dealing...

    so this can help with a lean tip in? im dealing with that issue also. I might try to increase that value to help with the lean condition. I cant feel it but my wideband shows it. when I lowered the...
  8. Replies
    9
    Views
    4,353

    Min fuel milligrams

    Is there a way to properly set this value for the injectors you use? I have searched but can't seem to find answer. I'm running Dekas 60's and my stock value was .028. My pulse width is 1.9 1.8 at...
  9. Thread: 2 bar upgrade

    by blown 04
    Replies
    3
    Views
    1,683

    Not sure. Downloaded it when it was first...

    Not sure. Downloaded it when it was first released. I emailed support about if I needed a newer version of 2.24 or I have to have 3.0 or do I just pay for the credits. Should it be free in 2.24?
  10. Thread: 2 bar upgrade

    by blown 04
    Replies
    3
    Views
    1,683

    2 bar upgrade

    Im still using 2.24 and trying to go speed density. when I go to write entire it wants me to buy more credits. I thought this was free with 2.24
    do I have to have 3.0?
  11. Replies
    7
    Views
    2,931

    Im going to try and unhook my bank 2 rear o2. I...

    Im going to try and unhook my bank 2 rear o2. I have them turned off in the tune. Cause I have my wideband. We're bank 1 rear o2 would be. Could this have a effect on the way the fronts work, because...
  12. Replies
    7
    Views
    2,931

    Yes idle and light cruise. I was thinking about a...

    Yes idle and light cruise. I was thinking about a cat issue? I was going to drop my y-pipe from the headers and see what happens. But that might screw o2 readings also if air gets sucked back up....
  13. Replies
    7
    Views
    2,931

    Always bank 2 is the leaner bank or the bank with...

    Always bank 2 is the leaner bank or the bank with the higher trim values
  14. Replies
    7
    Views
    2,931

    Thank you I forgot to mention that I have...

    Thank you I forgot to mention that I have replaced gaskets with new stock MLS a few times. Best I can tell no leak. But I will be checking again.
  15. Replies
    7
    Views
    2,931

    Help please! Fuel trim imbalance

    Im looking for possible causes for my trims being off bank to bank by as much as 6% sometimes more. This makes it impossible to try and dial trims in close to zero. TVS2300 came with marine Delphi...
  16. I PM'ed you

    I PM'ed you
  17. Replies
    0
    Views
    1,070

    slight cruise control issue

    can someone please look over my tune and help me get a slight cruise control issue im having? Truck will slow down but happens very slowly, gets real slow around 30mph and less. I have made some...
  18. Replies
    0
    Views
    1,034

    need help/ advice

    I know im suppose to post my tune when asking for help but I just installed deka 60 injectors and used my Banish dvd for the data so I don't want to post his
    info without permission. I have a 6 to...
  19. Replies
    9
    Views
    3,919

    I have been reading on here that some people zero...

    I have been reading on here that some people zero out the cracker table. What exactly does or will that do? This problem occurred when I installed my ls3 throttle body,
  20. Replies
    9
    Views
    3,919

    ok I will give that a try. First I made follower...

    ok I will give that a try. First I made follower decay and cracker airflow tables back to stock. still seemed like it wants to stay going, this is worse from 0-30 mph. like I said I have worked on my...
  21. Replies
    9
    Views
    3,919

    can you please enlighten me on what you see wrong...

    can you please enlighten me on what you see wrong with these tables? I thought my cracker airflow was stock but I did raise the decay table some. sorry for my lack
    of knowledge in this. should I...
  22. Replies
    9
    Views
    3,919

    tuning advice needed

    Ok been working on this tune for a while now and im wanting some advice on what I need to improve on. Just installed long tubes on truck with
    single 3'' exhaust system and I feel I lost power over...
  23. Replies
    2
    Views
    1,839

    Anyone? I know someone here can tell me how...

    Anyone? I know someone here can tell me how screwed up my tune is. this truck to me is not performing well at all. how can I get a more smooth running engine? as soon as I richen up the AFR the...
  24. what are your engine specs?

    what are your engine specs?
  25. Replies
    2
    Views
    1,839

    here is a short log its not much but at least it...

    here is a short log its not much but at least it shows that everything seems to be normal, o2s are moving, yes my bank 1 trim is slightly different from my bank 2. im starting to wonder about my...
Results 1 to 25 of 112
Page 1 of 5 1 2 3 4