Search:

Hey all,

I am logging accelerator pedal position [sensor] on my ETC 02 c5, and it seems perfectly correct for throttle position, except i have seen throttle positions greater than 100% ?

Any...

Additionally, i noted when i was going through a log i saved from when it crashed... The data points being read on the plotted graphs, did not correspond to the data in the chart. The AFR etc shown...

I'm late to the party on this one, but i am experiencing the same problem. I didn't realize there was a thread going on this issue.

I wont belabor the pont since it seems like you guys have made...

When creating logic for math filters....I had a question of the underlying calculation.



When the scanner applies a filter on play back, does it check EVERY time step from the scanner to...

Likewise, working like a charm now.


Appreciate the fast response from HPTuners, made for a much happier thanksgiving hahah

Bill... I would love to, but I need an actual installer to do so. I don't have the backup version. Just rolling it back to the restore point didn't fix it, and actually gave me all new errors.

...

Good to know I emailed him back a day or two ago and still haven't heard anything back yet.


Did you get a temporary solution then, or just screwed up for now?

Yeah, I've tried fully uninstalling it, tried rolling it back with restore. ccleaner and full install. Nothing I can figure out cleans it up and back to normal..

I tried to install 2.22, but...

After installing the current version, suddenly I have all sorts of scanner bugs.

Specifically the cylinder air mass shows no y axis values or units, the table no longer displays any units for some...

Lets see if i can brain dump this a little bit without running myself in circles... Been thinking on this all night...

Anyhow; Glad you chimed in marcin, i figured you could give me some good...

Just figured i would share my method in tuning Cyl Bias in my SD tune...


This has been something i have fought with over and over in trying to figure out the right method to attack it..

I...

Oh what i would give to have the Cylinder Charge Temp Bias availible in the RTT setup....

oh... and is there a better list of what tables are able to be gotten in RTT someplace...


the pull...

thanks for the excellent feedback! deffinatly the information i was looking for so thanks...

as per the stft feedback, the only reasoning i ever came up with for its exsistence, was for...

Just a random thought...

In the holden setups with Lean cruise.

1) does the file leave stft's enabled in open loop.

2) if the STFT's are enabled in OL, do they kick in during a lean...

your absolutely right unfortunately greg.....i wish i could argue the point, but theres nothing to argue.... its a compound of error situation.....

the best i can really say is i am certain i am...

lol dark side!


its not a timing issue(fairly confident), timing is great, and when idle kicks in does its job perfectly...

decel is fine, no bucking etc, nothing really happens to cause my...

Hey gang, was messing with the idle on my H/C car while i had some spair time... none the less... i was trying to pay particular attention to the follower and cracker, trying to see what they are...

got my email the same day as well... but im in AZ so i just assumed it was in the mail still :)

good info jay, again thanks for the response

so.... maybe a dumb question, but why the length of time in flipping them back out the door then....

im guessing the process isnt more complicated than downloading the old ROM uploading it to a...

again bill, thanks for jumping in...

the constant updates was more of a thinking outloud, though not a very difficult task to accomplish.... either way, i know the HPT crew has more to worry...

thanks for the response bill much appreciated...

the customer center just says "average turn around time 1 week"

but doesnt specify anything else...

something from my end that i think would...

wow, way to jump on this post an toss in an answer HPTUNERS people.....

im overwhelmed by the customer support.....

need i say.... its tasty.... looking at mine right now....

controller box is about the size of a us dollar bill

http://img.photobucket.com/albums/v645/GoatKart/lm-2/DSC00062.jpg
...

So, i went through the process on a unit(upgrading it from std to pro)... sent it in, the unit was apparently received today(signed for by keith today).... but i still havent seen anything about the...