Search:

Type: Posts; User: R0G3R

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Post your current tune file and log

    Post your current tune file and log
  2. Sounds like you need to dial in your VVE table to...

    Sounds like you need to dial in your VVE table to get a steady idle. After that you should be good to tune for the added airflow, driveability etc.
  3. Replies
    4
    Views
    1,457

    I would set your whole target idle speed table to...

    I would set your whole target idle speed table to the same rpm and give that a try.
  4. Replies
    4
    Views
    1,621

    Voltage issue? Ive had that happen before when I...

    Voltage issue? Ive had that happen before when I had a weak battery on customers vehicles.
  5. Replies
    4
    Views
    1,457

    Which file is currently on the car?

    Which file is currently on the car?
  6. Replies
    12
    Views
    2,905

    Have you calibrated your MAF and VE tables for...

    Have you calibrated your MAF and VE tables for the desired pe ratio?
    COT is still enabled, could be what's causing to get richer at WOT
  7. Replies
    18
    Views
    4,494

    post a log to be able to help you out

    post a log to be able to help you out
  8. Replies
    26
    Views
    7,914

    use this file to adjust your ve table fueling, i...

    use this file to adjust your ve table fueling, i have disabled closed loop and i have failed your maf so it goes strictly into SD

    .97696
  9. Replies
    26
    Views
    7,914

    sent you a pm

    sent you a pm
  10. Replies
    26
    Views
    7,914

    97668 try this file, i have updated the fuel...

    97668

    try this file, i have updated the fuel tables at idle areas, timing areas at idle and adjusted startup airflow. get a log of how it idles at hot restart.
  11. Replies
    3
    Views
    1,212

    https://forum.hptuners.com/showthread.php?67868-4l...

    https://forum.hptuners.com/showthread.php?67868-4l80e-segment-swap&highlight=12606960

    Read post #12, you might just have to do that.
  12. Replies
    1
    Views
    743

    Yes you can do a lower gear like 3rd gear if 4...

    Yes you can do a lower gear like 3rd gear if 4 speed to populate on higher load areas to dial in ve table correctly. I shoot for -1% to -3% error so it can still be good when you get a hot day.
  13. Replies
    65
    Views
    38,026

    Received my copy today as well! Will be watching...

    Received my copy today as well! Will be watching it these next few days.
  14. Your throttle drops from the desired 25% to 19%...

    Your throttle drops from the desired 25% to 19% kicking you out of PE.
  15. Replies
    6
    Views
    2,308

    90976 Here is the stock file. thanks!

    90976

    Here is the stock file.

    thanks!
  16. Replies
    6
    Views
    2,308

    Also I?m getting torque management advance, does...

    Also I?m getting torque management advance, does that mean I have to raise timing? On high/low octane tables.
  17. Replies
    6
    Views
    2,308

    My minimum speak table is -5 at idle, I don?t...

    My minimum speak table is -5 at idle, I don?t think that will help at all. The torque tables I raised and was able to get it to idle better. I will put the vtt tables back to stock and put minimum...
  18. Replies
    6
    Views
    2,308

    It?s only doing it when adjusting the virtual ve...

    It?s only doing it when adjusting the virtual ve table, could it be the virtual torque causing this issue?
  19. Replies
    6
    Views
    2,308

    cammed l83 stalling issues.

    I'm working on a 14 Silverado l83, has a tsp 227/235 110lsa camshaft, 3600 circle d converter. I'm able to get the truck to hold idle after I blip the throttle at start up after that itll hold idle...
  20. Replies
    8
    Views
    5,652

    Adjust your fuel at idle and part throttle with...

    Adjust your fuel at idle and part throttle with ltft, that?ll get you close enough and idle better.
  21. Replies
    8
    Views
    2,040

    Log Tcc slip

    Log Tcc slip
  22. Replies
    3
    Views
    1,464

    pm'd you

    pm'd you
  23. Replies
    3
    Views
    1,870

    6L80e not shifting on time

    I'm tuning my buddies car, its a 2011 Camaro ss 6.2/6l80e, it just has intake, headers and exhaust. I'm having issues with the transmission not shifting on time. I will attach the tune and log below....
  24. Replies
    2
    Views
    1,894

    Have you adjusted your injector flow data for the...

    Have you adjusted your injector flow data for the bigger injectors? Also have you done any changes to the VE or MAF table?
  25. Replies
    10
    Views
    4,773

    I messed with the timing and it helped it once at...

    I messed with the timing and it helped it once at operating temperatures. However, on a cold start it is still going into negative timing, does anybody have a idea on what table to modify to keep it...
Results 1 to 25 of 129
Page 1 of 6 1 2 3 4