Search:

Type: Posts; User: 94SS

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    4,860

    They messed the scanner up

    They messed the scanner up
  2. 2012 Camaro automatic trans bi directional controls?

    Has anyone verified they work on these cars? The engine and trans have been swapped into a 57 Chevy.
  3. Replies
    2
    Views
    1,922

    Are you talking about the throttle clean reset?

    Are you talking about the throttle clean reset?
  4. Replies
    2
    Views
    1,922

    E38 idle learning?

    Is their any parameters that can be added to the scanner that would allow you to see what the computer is thinking for idle feedback(integrators or PID learning)? And any other parameters related to...
  5. Thread: Dodge Progress

    by 94SS
    Replies
    1,138
    Views
    803,959

    Are any of the SRT-4 Neons part of the first...

    Are any of the SRT-4 Neons part of the first release?
  6. Thread: Dodge Progress

    by 94SS
    Replies
    1,138
    Views
    803,959

    Is it possible to tune NGC3 computers with HP...

    Is it possible to tune NGC3 computers with HP tuners if you want to use the beta software?
  7. The 98 Vette after about 100 miles and a key off...

    The 98 Vette after about 100 miles and a key off the message center started saying Pull Key and wait 10 seconds. That is with the Column lock set to not fitted and VSS to 255.
  8. I used the switch on a 98 Vette to Not Fitted and...

    I used the switch on a 98 Vette to Not Fitted and it didn't disable the column lock. We used one of his aftermarket relays and set VSS to cut column lock fuel to 256MPH and it seems to work. Is the...
  9. I found it under System>General>Column Lock. Is...

    I found it under System>General>Column Lock. Is the 97-98 Vette going to be supported they do not show this parameter?
  10. Where is it located in the BETA version?

    Where is it located in the BETA version?
  11. Replies
    9
    Views
    3,156

    Is there going to be a fix for the column lock...

    Is there going to be a fix for the column lock issues the C5 guys are having?
  12. Replies
    9
    Views
    3,156

    The file still ask that you send it to support...

    The file still ask that you send it to support with 2.1.18 but it was read from the car with you previous version.
  13. Replies
    9
    Views
    3,156

    The original hpt. file I sent in still doesn't...

    The original hpt. file I sent in still doesn't open but the one I got back labeled _fix does.
  14. Replies
    9
    Views
    3,156

    All I got was a file back named _fix last year. ...

    All I got was a file back named _fix last year. I just wanted to make sure I was ready so the customer doesn't have to wait.
  15. Replies
    9
    Views
    3,156

    1998 Corvette File not supported?

    If you have previously sent in a stock file for one of these that says Definition failed to load. Please e-mail this file to support at hptuners dot com Is it OK to do a full rewrite with the fixed...
  16. Replies
    2
    Views
    2,123

    EFI Live custom operating system?

    Can you read these with HP Tuners or are you locked out and have to start with a fresh tune?
  17. What are you using for voltages(0 volts 10AFR and...

    What are you using for voltages(0 volts 10AFR and 5 volts 18AFR)? And what works best for sampling rate with the LM-1? Thanks.
  18. Which cam is that? I remember seeing something...

    Which cam is that? I remember seeing something like that and somebody had already messed with the TB stop. I have never understood why the only way to lower IAC steps is to drill or crack the...
  19. Replies
    20
    Views
    11,809

    What effects do the first three columns of the VE...

    What effects do the first three columns of the VE table have on idle control if you are still using a MAF are they part of Desired IAC airflow? You would think since the MAF is still plugged in it...
  20. Replies
    20
    Views
    11,809

    Here's a good link that explained a little bit...

    Here's a good link that explained a little bit more for me.

    http://www.hptuners.com/forum/showthread.php?t=1645&highlight=throttle+cracker+settings
  21. Replies
    20
    Views
    11,809

    Is it possible to get rid of the brief 300 RPM...

    Is it possible to get rid of the brief 300 RPM drop that you get when you put a A4 in reverse with a good sized cam. I have been looking through all the tables and it don't look like there is...
  22. Replies
    20
    Views
    11,809

    Anyone have problems with IAC trims? I had -.5...

    Anyone have problems with IAC trims? I had -.5 in Park so I took out .25 from your Running Airflow Table and then it shoots to the max of LTIT .5 . What is the cause of this problem?
  23. Replies
    42
    Views
    64,478

    I found this in the help file. 2 Bar MAP -...

    I found this in the help file.

    2 Bar MAP - Speed Density

    This enhancement contains the following features:

    2bar MAP sensor support (calibration capability for GM 0-5V linear MAP sensors) ...
  24. Replies
    42
    Views
    64,478

    Where do find good information to get started...

    Where do find good information to get started with the custom speed density tune I did not see anything in the help file?
  25. Replies
    20
    Views
    11,809

    How do you come up with the gm/sec values for the...

    How do you come up with the gm/sec values for the IAC park position vs. IAT or does it even play much factor in idle tuning? All I have heard is everything above 40 Degrees celcius make 21.
Results 1 to 25 of 30
Page 1 of 2 1 2