Search:

Type: Posts; User: Dusty05

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    2,683

    I was told to watch manifold temp, thermal...

    I was told to watch manifold temp, thermal protection is most likely from that. I am running a 2.65/ati combo so I am overspinning a little bit. What combo are you running?
  2. Replies
    12
    Views
    2,683

    Just ran into the same issue tonight on my trx....

    Just ran into the same issue tonight on my trx. Right before the 1/4 mile mark also. Injector pulsewidth is fine, I?m wondering if it?s trying to protect the cats.
  3. Replies
    9
    Views
    4,526

    I had to do this on my trx, did it work on your...

    I had to do this on my trx, did it work on your truck too?
  4. Thread: 2019 trucks

    by Dusty05
    Replies
    5
    Views
    2,360

    The 2019 trucks have the same afm setup, but I...

    The 2019 trucks have the same afm setup, but I already lost interest at the different connector ordeal. 😂
  5. Thread: 2019 trucks

    by Dusty05
    Replies
    5
    Views
    2,360

    2019 trucks

    I've read all the bad news on the new ecms. I've been kicking around ideas around this. Has anyone tried a Vette ecm in a truck, or are the connectors different?
  6. Replies
    5
    Views
    1,929

    I want to upgrade to the MPVI 2

    Tried to respond on the other post but its locked. I see there's no eta on Switching our licenses from MPVI->II. Kind of rude to be selling these units to people who haven't even used the product...
  7. Replies
    4
    Views
    2,316

    I miss the old scanner that worked just fine on...

    I miss the old scanner that worked just fine on 3800s
  8. Thanks Ed!

    Thanks Ed!
  9. I'm only getting one line of data across the top

    Probably something simple I'm missing here. I'm trying to log spark on rpm vs aircharge. I can get the full table to work with rpm vs map but that doesn't help me as much.
    Here's a screenshot
    ...
  10. Thread: 2018 Support?

    by Dusty05
    Replies
    4
    Views
    2,027

    Another question Bill, should I stay away from...

    Another question Bill, should I stay away from the E Assist hemi if I want to tune my 2019 one day? I noticed we stayed away from the hybrid GMs in the past.
  11. Thread: 2018 Support?

    by Dusty05
    Replies
    4
    Views
    2,027

    Bump I'm getting a 2019 now so I'm guessing...

    Bump

    I'm getting a 2019 now so I'm guessing that's way out. lol

    I have been getting asked for ETAs on 2018 support though
  12. Thread: 2018 Support?

    by Dusty05
    Replies
    4
    Views
    2,027

    2018 Support?

    I've been considering going to a 2018 from my 2015, will 2018 be supported? I see its not listed yet.
  13. Replies
    13
    Views
    7,110

    Has your pcm previously been hacked up by diablo...

    Has your pcm previously been hacked up by diablo sport or something similar in its lifetime?
  14. What table is slip times located?

    What table is slip times located?
  15. I got it figured out, I didn't hit every single...

    I got it figured out, I didn't hit every single "mode" on the new settings. Also noticed it'll rev up quicker and higher than command propshaft speed, so be prepared to command a few hundred rpm...
  16. 8 speed trucks. Adjusting shift points. Normal table?

    To adjust shift points, wouldn't we adjust the normal table on pickups? I see there's snow, mud, perf, tow, etc.

    Yesterday I adjusted it so it *should* be shifting at 6k across all gears and it...
  17. Replies
    7
    Views
    4,268

    oops I meant RPM lol

    oops I meant RPM lol
  18. Replies
    1
    Views
    1,694

    Can you throw up a pic of the table? If its the...

    Can you throw up a pic of the table? If its the one I'm thinking of, I went to 0, but everyone says I'm brave lol
  19. Replies
    7
    Views
    4,268

    How much higher are you going on the shifts?

    How much higher are you going on the shifts?
  20. Replies
    3
    Views
    2,926

    I'll be licensing mine soon to play around on my...

    I'll be licensing mine soon to play around on my 2015 RAM. Right now I have all TM off on the engine side tables. It's been like this for almost 3 years now with lots of racing. I'm also curious how...
  21. Sticky: Great work guys! Now I have to research what some...

    Great work guys! Now I have to research what some of these tables do and what not to touch lol
  22. Replies
    9
    Views
    5,486

    I was going to say, I doubt you did anything...

    I was going to say, I doubt you did anything wrong. I pulled all the AVAILABLE TM out of my Ram and it's shifts beautiful years later.
  23. Replies
    16
    Views
    12,206

    I remember a GM engineer saying this back in 2014...

    I remember a GM engineer saying this back in 2014 :cool:
  24. Replies
    10
    Views
    5,580

    Yeah I'm not very happy with the drivability of...

    Yeah I'm not very happy with the drivability of my Eurocharged tune on the E55. Hoping these will be supported one day too.
  25. Replies
    15
    Views
    14,942

    I would like to beta test the E55 :D

    I would like to beta test the E55 :D
Results 1 to 25 of 188
Page 1 of 8 1 2 3 4