Not sure on the ve table numbers but I've only gotten to 2k cleaned up. I'm just working from the mail order tune.. I gave up on the tuner, but in the end it wasn't his fault, engine builder advanced...
Type: Posts; User: ZJM861
Not sure on the ve table numbers but I've only gotten to 2k cleaned up. I'm just working from the mail order tune.. I gave up on the tuner, but in the end it wasn't his fault, engine builder advanced...
I am in the mists of getting the VE tables in order and one thing I have noticed is fan 1 and 2 is coming on at like 100* for what seems like the minimum duration of fan operation in the tune. This...
Sonna b.. I knew there was this feature and it was removed :pray: hopefully they add the Marker feature back.. it will make diagnosis a bit easier.
We are only modding the secondary ve table since we have open loop disabled/doesnt read the main ve table. Or do i need to copy and paste the values to the main ve each time I flash it? I lm sure I...
Thanks for the info :)
firing order in the tune is different than all tunes I've compared to.. the entire firing order is shifted over to the right.
attached is a picture of mine, top, and the compare file on the bottoom....
65023
tune is incomplete, a coworker is VE tuning it when time permits but shows egr enabled
I only connected the voltage output from the controller to 55, and the pin 41 was the controllers ground wire (sensor wire, not heater ground). Then I tried using only pin 55, and a separate chassis...
I have installed a 99 Camaro engine/trans into my BMW and have been running it for about 2 years. Recently bought and installed a wideband controller and installed the output to C1 Blue pin 55. The...
Hi, Quick question, I am looking at the tune file for my car, 99 BMW 528i with a cammed 5.7 4l60e with a truck MAF sensor. I am looking at the MAF calibration, airflow vs frequency and the numbers...
I did a swap with a 2015 LT1 in a '68 back in February and back then with the current version of hp tuners, it only listed Vats1. 2014 tune files showed vats 1 and 2. After a while.. lots of...
update:
after disconnecting it from the can lines, HPTuners operated properly. Editor worked flawlessly read/write and the ecu functions in scanner worked. Went ahead and did a write calibration and...
I didn't even consider disconnecting them, I will give that a try and report back. Thanks for the tip
same thing here, downloaded the latest yesterday and same thing, i'll email support with the required info you requested. thanks Keith
I am the tech that wired the truck and diag'd to vats.
update: it does run now
update: see help post:...
Read ECU successfully (hp tuner version before 2.5 BETA) and it showed VIN/OS error unable to apply credits. Sent ECU to tuner to disable VATS for the swap.
Once the ECU was revived, truck ran....
I just flashed the 69 Silverado w/ 2014/2015 hybrid ecu and was successful. Reason its a hybrid ECU is it was sent to the tuner for them to erase VATS to start with and then once running, I would use...
update:
hpsupport replied to an email, it will require license ecu and downloaded tune file
Hi, after comparing my ecu file from 2014 5.3 Silverado with 3 other 2014 5.3 trucks, the important different is VATS 1... mine does not show VATS 1, only VATS 2... and its currently disabled as this...
Last idea I had was get another 2014 Silverado, remove the ECU, take mine change the vin number to match the other 2014 Silverado and see if our ecu runs... only don't know if all 2014 ecu's are the...
Hi everyone, I have a 2014 5.3 gen 5 engine/trans swap nearly done except well, it doesn't run. I am using the factory fuel pressure sensor, fuel pump module and fuel pump assembly to minimize...
Bummer, I found some more threads and its doesnt look good with hptuners. EFI live can do it no problem.. lol.. and i dont have that equipment. In the thread they talked about efi live can flash the...
I am in need to change the VIN # in the pcm and it says "invalid vin" when entering the vin of the current (swap) vehicle. Is there a work around to entering vin numbers? I am swaping a LS into a...
I just bought a 2000 e46 for 3 reasons. 1- I realy like the body style. 2 - LS swap. 3- Priced right.
Getting the engine/trans in - dont expepct problems
Getting the engine to run - no problem...
Is there a diagram for this pinout? I dont program the truck much, but my buddy used it much more than I do. I'd like to splie into the back of the obd port and run the wires to the same style...