Search:

Type: Posts; User: Road

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    22
    Views
    14,214

    Depends on how safe you want the A/F ratio but...

    Depends on how safe you want the A/F ratio but 12.8 @625rwhp on race fuel will start taxing the HPFP.
  2. Replies
    49
    Views
    30,891

    :rolleyes::rolleyes::rolleyes::rolleyes:

    :rolleyes::rolleyes::rolleyes::rolleyes:
  3. Replies
    4
    Views
    2,183

    Make sure you are using the beta software

    Make sure you are using the beta software
  4. Thread: LML Tuning

    by Road
    Replies
    39
    Views
    40,162

    I don't data log much with the scanner on lml....

    I don't data log much with the scanner on lml. But my pro has very little support last time I did data log with it.
  5. Thread: LML Tuning

    by Road
    Replies
    39
    Views
    40,162

    Read the truck hpt will give you a stock file...

    Read the truck hpt will give you a stock file when you do a read
  6. Replies
    2
    Views
    2,856

    Most likely it is a torque error I would use...

    Most likely it is a torque error I would use table 14291 and 14292 to address the issue.
  7. Replies
    3
    Views
    1,485

    Thanks Bill Normally no error reported gives me...

    Thanks Bill
    Normally no error reported gives me a no start. There is no maf on the truck and the dtc's are set the same as the as the 1 bar tune that it runs on.

    Should it be set to "no mil"?
  8. Replies
    3
    Views
    1,485

    No Start After 2 Bar COS Update

    I have a P59 12592618 That when I apply the 2 bar upgrade the truck is a no start with dim injector pulse (low ground injector driver). I have also flashed know good 2 bar file into it and still its...
  9. Thread: Second MPVI

    by Road
    Replies
    4
    Views
    2,678

    Keith I am trying to export a e38 file to Ngauge...

    Keith I am trying to export a e38 file to Ngauge but there is no Export under the file tab. That's why I added a second MPVI for single licensing to export files. Do I need unused credits for the...
  10. Thread: Second MPVI

    by Road
    Replies
    4
    Views
    2,678

    Thanks Keith I thought I needed to add a ID and...

    Thanks Keith
    I thought I needed to add a ID and Key.
  11. Thread: Second MPVI

    by Road
    Replies
    4
    Views
    2,678

    Second MPVI

    I am trying to add a second cable and I thought there was a way to have 2 MPVI connected to the editor at the same time. Can some one point me into the right direction to add a second interface...
  12. Replies
    5
    Views
    6,852

    You can't read a LML from the obd port. The only...

    You can't read a LML from the obd port. The only way to read one is to remove the back cover and read it. You can buy a handheld with tunes and write it through the obd port. Being it is deleted then...
  13. Replies
    17
    Views
    8,149

    Send a email to support with the screenshot from...

    Send a email to support with the screenshot from H&S and ask them to add it.
  14. Thread: Segment Swap

    by Road
    Replies
    0
    Views
    1,197

    Segment Swap

    I have a 1999 Silverado and the operating system doesn't support segment swap but way back it was sent to HP Tuners and a 4L80 segment was done in house. That ecm now has a bad injector driver. I...
  15. Set the whole table to a positive number and it...

    Set the whole table to a positive number and it wont pull any fuel when you hit the limiter.
  16. The LML has many limiters most we don't have...

    The LML has many limiters most we don't have access to. I leave them all stock and just use table 18994. that seems to override all limiters.
  17. Hp Tuners added the table for me about a year ago...

    Hp Tuners added the table for me about a year ago and have been working for me. Use table 18994 the one right beside all the limiter speed settings. "Limit by fuel reduction"
  18. Does it read the ecm or is it a virtual read?

    Does it read the ecm or is it a virtual read?
  19. Replies
    10
    Views
    4,088

    Will this work

    Will this work
  20. Replies
    7
    Views
    6,170

    That's awesome! What gear and load did you make...

    That's awesome! What gear and load did you make the pulls with? I have a DC6000 Generally see those numbers without spray with the right load and boost. Thanks
  21. Replies
    4
    Views
    3,234

    I can hook you up

    I can hook you up
  22. Replies
    6
    Views
    2,720

    What year model and type of car?

    What year model and type of car?
  23. Can you make this one work?

    Can you make this one work?
  24. I think the only way people are unlocking the...

    I think the only way people are unlocking the Cummins is with Bully Dog and a unlock cable and there is a connector under the hood you use to unlock them. The gassers have to be opened up and done...
  25. I have a tune from a 08 that I tuned with a...

    I have a tune from a 08 that I tuned with a similar setup I can send you for comparing. The checksum is off because I added tap shift to the tcm though. PM me if you need help.
Results 1 to 25 of 481
Page 1 of 20 1 2 3 4