Search:

Type: Posts; User: Gonzalo Bravo

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    1,278

    VVS Signal E38 ecu/ L99

    Hi

    The source of the speed signal that feed the speedo in the 2012 Camaro L99/LS3 came from this wires???:

    71 0.5 GY/BK 6355 VSS Signal High (M10)
    72 0.5 PU/WH 6356 VSS Signal Low (M10)
    ...
  2. Replies
    0
    Views
    1,325

    Tap shifting on 6L80

    Hi

    I am installing a L99/6L80 (2010) on a 4wd car. I check the wiring harness but cant see any wire that can be use the donor car to shift gear with the paddles. Neither an extra plug in the ecu...
  3. Does this works?? I need to to the same on a...

    Does this works??

    I need to to the same on a 6L80.
  4. Replies
    2
    Views
    2,053

    Righ, the 6.5 Turbodiesel.-

    Righ, the 6.5 Turbodiesel.-
  5. Replies
    2
    Views
    2,053

    L56 supported?

    Is the L56 (Vin S) supported with HP Tunner?

    Thanks in advance!!
  6. Replies
    10
    Views
    5,722

    Is there any modification on the wiring harness...

    Is there any modification on the wiring harness to use without the VVT?
  7. Replies
    10
    Views
    5,722

    Nelson Performance tune the ecu for their own cam...

    Nelson Performance tune the ecu for their own cam kit. But what you say about the harness for non vvt? The only that I did was left the vvt actuator switch un connected. Is there any special mod in...
  8. Replies
    10
    Views
    5,722

    The engine comes with the light brown sensor...

    The engine comes with the light brown sensor (12591720) and tbe vats is off.

    If I chech that part number shows me that came on LS engines.

    So, the vvt sensor that remain there looks the same as...
  9. Replies
    10
    Views
    5,722

    Well, my engine is on a stand right now, not on a...

    Well, my engine is on a stand right now, not on a car
  10. Replies
    10
    Views
    5,722

    Whar a security relearn is? Thanks in advance!

    Whar a security relearn is?

    Thanks in advance!
  11. Replies
    10
    Views
    5,722

    grounds are ok, no DTCs, etc. Any idea????????????

    grounds are ok, no DTCs, etc. Any idea????????????
  12. Replies
    0
    Views
    1,275

    No DTC with sensor disconneted

    I tried to run an L92 with the wrong camshaft gear cover, and told me P0340 DTC (camshaft possition sensor). Problem was the cover leave the sensor to far to the new non vvt gear. Replace the cover...
  13. Replies
    7
    Views
    5,159

    But can you keep the VVT sensor with non VVT...

    But can you keep the VVT sensor with non VVT cover (shorter) or needs to put a non VVT sensor too?
  14. Replies
    10
    Views
    5,722

    L92 dont starts

    Hi guys.

    I am working on a L92 with manual transmission that I switched the VVT camshaft for a more agressive one.
    To do it, I change the cam gear for a non vvti cam with his shorter cam cover....
  15. Need to read NGC4A/GC4A . I have the plugs

    I need to read the program of a NGC4A and a NGC4.
    I have the connectors from a cut harness, but wich one is needed? Some one have the pinout of a RAM hemi 5.7 2011 to pick the OBD2 wires????
    ...
  16. Replies
    14
    Views
    13,016

    Thanks. You know who can tune this?

    Thanks. You know who can tune this?
  17. Replies
    14
    Views
    13,016

    Hi guys I am planning to swap a 2011 RAM's...

    Hi guys


    I am planning to swap a 2011 RAM's 5.7 HEMI on a Wrangler TJ.
    I have 2 ECUs, one out of a ~2008 5.7 HEMI (attached picture) and the donor ECU.

    Questions are:
    Are both the same?
    If...
Results 1 to 17 of 17