Does anyone have a stock read they could provide me with for 2020 5.7 A8 RAM with 68455112(XX) variant?
Type: Posts; User: APS
Does anyone have a stock read they could provide me with for 2020 5.7 A8 RAM with 68455112(XX) variant?
Good grief that's frustrating. Makes me want to go buy one and start banging away at it by some other means. I wouldn't mind spending a ton of time on it if I felt like I was gaining ground but I...
Glad I found someone I trust also fighting this. After years of VVE working flawlessly and Gen5 becoming even easier for me to make drive nice than some of the Gen4 stuff I find this NN trainer...
I have a fought an issue with a bone stock 2018 LTZ for a week and a half in my spare time between other appointments. This truck, nearly every time you accelerate soft from a stop after being...
Why is this GEN4 post in the GEN5 section?
[QUOTE=Jim P;711806]What is it that you swapped??? Did you put a 5.9 in a 2016??? Did you put a 6.7 in a 2006??? 48RE??? 68RFE??? 2006 ECM??? 2016 ECM??? Were sensors properly rescaled??? ...
The only thing displayed is exchange service and "out of stock". I just want to get it unlocked like all the others I have already had done.
Thank you.
Everything I need is listed in the title or any AA - A(x) should be fine.
Was this condition resolved? I haven't seen this before and am wondering what the solution was if any.
That's so irritating. I thought about a valve body or shifter switch swap if I had to, but now it looks hopeless with also having to properly signal the ECM also.
I have a 2020 GMC L84/MQE 8spd here with the T93 in it. There is an older thread about possibly using a T87a in this application. Has that ever been sorted out? Happy to pay for a compatible VIN or...
For all those who don't know, spoofing the FICM does work within reason. However there are potentially severe side effects. Be careful, make changes in moderation and always datalog what's going on. ...
Did you seriously say "No, cant be done. Not supporting 7.3. Those PCM's have the J3 port for chips."?
I guess that would make you an authority then. All except for the fact I have been flash...
So I have a 2011 RCSB here swapped by a local shop.
Original truck 2011 4.8L 4L60E variant.
Donor 2013 A6 harnesses and modules inside and out with 6L80E installed.
FAULT: No tachometer...
What exactly is your combination? Care to post a file?
No. The car will literally run perfectly fine for years. I just looked back at my files. The last time this same operation fixed the car was almost exactly 5 years ago. Then the car will go into a...
BACKGROUND
Condition:
Recurring "Reduced Engine Power", "P0606", "Engine Disabled". No faults found.
I do some web searching for the condition and find a full write of the ECM potentially...
I made this a long time ago while studying to familiarize myself with Chrysler fueling. Maybe someone will find it useful.93214
Does the Zautomotive tool: https://www.zautomotive.com/zpu/instructions/DurangoGCSCWBypass.pdf ---which I already own work with HP Tuners on this vehicle in conjunction with the MPVI1?
This method is F****** retarded. I?m spending my money to put credits on another persons cable but I have to have their application key to register their cable on my account. It?s not the damn NSA.
I really need a like button on this post. LOL
I am in the middle of Oklahoma but I tune loads of KS cars. As far as cars from other states, I tune more from KS than any other surrounding state.
My installer folder is humongous. LOL
Well after all that crap I tried to disable WOT fuel trimming by setting ect to go closed loop to 280, turned STFT in open loop back on and nope it still does the same thing. So it left here in OL...