Thank you for your quick reponse
Type: Posts; User: MEC 02 TA
Thank you for your quick reponse
Can anyone suggest what I may be doing wrong? I am trying to get my AEM wideband to record in standalone, It works while scanning while hooked to the computer but when I do stand alone logging it...
Thanks for the response, the misfires come and go,I did clear out the code and it did not come back for several days, but then I turned on the airconditioner and it came back. I put a misfire config...
Hi all
Is anyone using the AEM Inline Wideband UEGO Controller? If so, can you tell me how it works? I am in the process of purchasing a wideband controller and I am looking for a good unit, any...
Hi Eagle
I live in the suburbs of Chicago, I have done some idle tuning but know i need to do more. Right now I am working to get the car to the inspection station before i start tuning more. Being...
Hi all here is the log from tonight, I made a couple of small changes first, around frame 2271 I was at around 78mph with no issue with drive ability, but around frame 4533 it appears the fuel cut...
Hi tpcaz, thanks for the suggestions. I will look for the crank setting. Do you have a sample tune that you use that i could use as a reference? Again thank you for all of your suggestions.
Thanks...
Hi Eagle, I will take it out tomorrow to pull more a scan, the first part of the one posted was the warm up. I have not done anything with Tourque Managment yet. I was trying to get the timing and...
Hi all
Can you please look at my tune and tell me what you think? The car runs good, and idles fine a little rought but that could be the cam. It has good pick up, everynow (not that often) and...
Hi all,
I have been driving my car every day for the last 7 days, the Catalyst and Oxygen Sensor Heater are still showing incomplete, today I drove about 20 miles out stopped for a while and then...
Hi all, When checking my DTC's readiness, my vehicle information and Diagnostics information tabs are always blank. The Emissions, Readiness States tab has the correct in formation. Is this correct...
Hi all, I have been adjusting my tune and it seems to run pretty good, however I am having a couple of issues. After it is warm, if I turn on the air, the throttle will stay high (2000) for 30 sec or...
Thank you
Hi Chris,
I was able to disable the P01021 code, but I am not sure what to change to disable the P0106, do I modify the tables in Engine Diagnostics>>P0106 Max and min tables if so do I just take...
Thanks Chris, in the scanner I am not getting a P0106 code, and in looking at my settings I am set at 0 for my min Map vs gear setting and 0 for my Max TPS vs RPM vs Gear, do you think I should...
Hi all
I have been working on my Idle for a couple of days with some help of some tuners on this site. I think I am close, I am getting a little surging for a min or so and then it settles back...
Hi All
I changed adjusted the throttle blade to allow more air, I also adjusted the timing and the overspeed and underspeed files, it starts better cold but when warm it is a little sluggest...
Thank you, I found it, I thought that was a pin but was able to get it to turn, thank you for your help
Mark
Great thank you, I will work on that today.
I looked but did not see a set screw on the TB, I go over it again in the light today.
Thank you for all of your help
You said to muliply the entire table by 25%, is that the BRAF or the MAF table, also do you mean to increase my numbers by 25%? Also how do I open the throttle blade?
Thank you for your time..
Mark
Thank you, I will try that today. Here is the config file
Hi all
I am new to tuning; I have been reading and learning everything I can from the forum and online. Can you all please take a look at my files and tell me what you think. I do have a couple of...
Hi all
Mark from Chicago, I have a 2002 Trans Am, LS1. I have added some bolt on's and a cam. Installed and set up my HPTuners Pro version end of last week. Still reading through all the...
Hi all
I am new to tuning; I have been reading and learning everything I can from the forum and online. Can you all please take a look at my files and tell me what you think. I do have a couple of...