Search:

Type: Posts; User: Wangspeed

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    5,902

    So, according to GPS, 26715 ppm is the right VSS...

    So, according to GPS, 26715 ppm is the right VSS setting. As far as the FD ratio, I changed it to 4.05, and there seem to be no ill effects. The HHR SS GMPP tune has 1:1 in it, but the VSS is set...
  2. Replies
    12
    Views
    5,902

    Tom do you have an HHR file you can send me?

    Tom do you have an HHR file you can send me?
  3. Replies
    12
    Views
    5,902

    Interwebz has failed me. Which number is...

    Interwebz has failed me.

    Which number is which? If they're not talking about actual gear ratios, I don't know if the first or second number represents the stock value.
  4. Replies
    12
    Views
    5,902

    Thanks for the info. Still a little confused...

    Thanks for the info. Still a little confused about the ratio though. I would think it would be either .94:1 or 1.06:1. Stock HHR SS has 1.03 and lower PPM? Totally confused on that. I would have...
  5. Replies
    12
    Views
    5,902

    Also, if someone else has access to an HHR tune,...

    Also, if someone else has access to an HHR tune, would you see how many VSS pulses per mile it is set to?
  6. Replies
    12
    Views
    5,902

    Final Drive Ratio

    I assume that by going from 3.82 -> 4.05 that I should change the FD ratio from 1:1 to .94:1. Is this right, or did I get it backwards?

    The help file wasn't very helpful for this. I wasn't...
  7. Replies
    17
    Views
    6,920

    Check for codes. Betting there is a boost leak...

    Check for codes. Betting there is a boost leak if you see boost hit 5psi, hang for a sec, and then go up. Or you have poorly wired/dirty (T)MAP sensors.
  8. Sorry, I failed reading comprehension, I guess.

    Sorry, I failed reading comprehension, I guess.
  9. LNF has a wideband in the O2 housing, and a...

    LNF has a wideband in the O2 housing, and a narrow band in the downpipe, after the cats.

    It seems that I'm in the minority on this board. I love all the instrumentation that this car provides...
  10. I think it's time for a leakdown and compression...

    I think it's time for a leakdown and compression test. At least it's easy to do on this motor.
  11. Replies
    1
    Views
    1,582

    Not the same lap, but it's the same turn. Proof...

    Not the same lap, but it's the same turn. Proof that it's over 1g of lateral load, plus WOT.
  12. Replies
    1
    Views
    1,582

    1g lateral loads + WOT = yikes

    I was wondering why I heard some compressor surge on WOT while on track. It's because load is tremendously high in load speed turns, and boost is going way higher than intended. My turbo is...
  13. Replies
    66
    Views
    41,970

    Thanks for sharing, John.

    Thanks for sharing, John.
  14. Replies
    29
    Views
    17,893

    I threw in the towel. It must be different on...

    I threw in the towel. It must be different on the 09 ECUs. Mine would never go ready for cat state. Went back to stock DP and a tune with P0420 enabled to get it past emissions.
  15. Replies
    29
    Views
    17,893

    Which codes did you set to 0? I think mine is...

    Which codes did you set to 0? I think mine is only disabling P0420. Maybe the P013* codes. I don't recall off the top of my head now. Not on a computer w/ HPT.
  16. Replies
    29
    Views
    17,893

    I've been out of town, so I haven't been able to...

    I've been out of town, so I haven't been able to drive it to set it, which sucks, because my registration just expired.
  17. Replies
    29
    Views
    17,893

    I dunno why some of you guys don't believe me. ...

    I dunno why some of you guys don't believe me. I'll post a SS after it sets. Pick option 0 - Disable. It set every OBD2 readiness monitor to Ready state.
  18. Replies
    29
    Views
    17,893

    It's set to disable, option 0. It set O2...

    It's set to disable, option 0. It set O2 readiness on the car I tuned, despite the fact that I disabled it, which surprised me, but also made me quite happy. Saves me from having to swap the stock...
  19. Replies
    29
    Views
    17,893

    I checked another car I tuned around here, and it...

    I checked another car I tuned around here, and it does go ready eventually, so I guess it's back to driving. Thanks folks.
  20. Replies
    29
    Views
    17,893

    Gonna another local LNF that I tuned to see what...

    Gonna another local LNF that I tuned to see what his readiness states are. If his set, I'll just keep trying to do the damn readiness procedure.
  21. Replies
    29
    Views
    17,893

    Sorry, I'm used to everyone talking LNF on this...

    Sorry, I'm used to everyone talking LNF on this forum. I forget there are other engine types on this subforum.
  22. Replies
    29
    Views
    17,893

    Attached

    Attached
  23. Replies
    29
    Views
    17,893

    OBD2 Readiness, P0420

    Okay, so I have a high flow cat, which has no angled bung, and it throws P0420. No problem, disable right? Well, 2 years later, it is time for emissions, and since I have it disabled, apparently...
  24. Replies
    9
    Views
    5,236

    I trimmed about a 1/4 away in a small area and...

    I trimmed about a 1/4 away in a small area and tweaked the shield a bit. It's pretty much all gone now. Back to normal! Just used some left and right tin snips and a file, and painted after. I...
  25. Replies
    9
    Views
    5,236

    Ugh. I know it shouldn't worry me, but it...

    Ugh. I know it shouldn't worry me, but it doesn't give me a warm fuzzy. I probably wouldn't worry about it if it was a ball bearing CHRA, but under decel, the oil pressure is dropping, so I worry...
Results 1 to 25 of 45
Page 1 of 2 1 2