Search:

Type: Posts; User: Waker

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    2,580

    Ok got it, they just moved it under edit,...

    Ok got it, they just moved it under edit, gear/tire wizard.
  2. Replies
    2
    Views
    2,580

    Tire size and gear calculator 3.0

    I'm not seeing any tire size inputs. Having said that, can we please get the gear/tire calculator from 2.24 back.
  3. I think I got it figured out. Since there is no...

    I think I got it figured out. Since there is no IAT2 table to adjust (Bill please add), I have to re-cal the IAT2 sensor so it does not pull so much timing.
  4. 2015

    2015
  5. 2015 ZL1 M6 not following High/Low Octane table

    As the title reads, this ZL1 is not following commanded timing. I must be missing something. It is at times 10 degrees off at WOT. I had to add to the AFR/Gas correction table to get the timing back...
  6. Sorry :)

    Sorry :)
  7. 2015 ZL1 M6 not following High/Low Octane table

    I must be missing something but I can not for the life of me figure out why this particular ZL1 is not following anything remotely close to commanded timing. I actually had to get the timing back up...
  8. Replies
    2
    Views
    1,784

    Have you disconnected the cannon plug and reset...

    Have you disconnected the cannon plug and reset it? Can you actually feel the detents changing in the TCM? The 6L has a park paw, so it sounds like your not even getting to Park internally.
  9. Replies
    18
    Views
    13,158

    Cool, so there is a new Beta?

    Cool, so there is a new Beta?
  10. Thread: 3rd gear lockup

    by Waker
    Replies
    1
    Views
    1,771

    Try matching your 3rd and 4th lockup speeds to...

    Try matching your 3rd and 4th lockup speeds to the 3rd gear settings. Lower your release speed by 10 MPH. See what that gets you.
  11. Replies
    2
    Views
    2,311

    You still have %100 TM in your tune, your only...

    You still have %100 TM in your tune, your only lowering your shift times, wch in turn decreases the time Torque is pulled.
  12. Replies
    18
    Views
    13,158

    You tried tweaking "Spark Minimum Tqt Mgt" to see...

    You tried tweaking "Spark Minimum Tqt Mgt" to see if it lessens?
  13. The shift times need lowered. The adaptives will...

    The shift times need lowered. The adaptives will continue to pull line pressure in an attemp to meet the desired shift time. Removing more TM will only worsen the problem.
  14. Replies
    13
    Views
    6,909

    Made a couple changes to the 2011 file. Try those...

    Made a couple changes to the 2011 file. Try those and let me know...
  15. Replies
    2
    Views
    2,396

    How warm is the tranny, and are you sure it's...

    How warm is the tranny, and are you sure it's full of fluid. If it holds 4/5/6 in TUTD the clutches are usually fine.
  16. Replies
    20
    Views
    16,580

    I have to piggy back...TM is a must if you want...

    I have to piggy back...TM is a must if you want cleaner shifts and trans longevity. So many guys are quick to just turn it off :banghead:
  17. Replies
    142
    Views
    104,509

    Dangerous is good...:D

    Dangerous is good...:D
  18. Replies
    5
    Views
    6,309

    You need a good tune...

    You need a good tune...
  19. Replies
    116
    Views
    126,866

    Also, make sure the clutch purge function is...

    Also, make sure the clutch purge function is enabled in your tune.
  20. Replies
    116
    Views
    126,866

    Disconnect the battery for about 30sec, that will...

    Disconnect the battery for about 30sec, that will reset the TCM. Then reinstall the beta and start from scratch.
  21. Replies
    116
    Views
    126,866

    Its not communicating correctly. Try the above...

    Its not communicating correctly. Try the above steps and see if that helps.
  22. Replies
    116
    Views
    126,866

    Have you flashed with the new beta? Don't know if...

    Have you flashed with the new beta? Don't know if that may be holding you up. This thing is soo tricky...
  23. Replies
    116
    Views
    126,866

    Go into your...

    Go into your "Documents/HPTuners/VCMScanner/Vehicles" folder and delete the .os files. This will force the scanner to re-poll the ECM for supported PID's and see if it comes up.

    This may help...
  24. Replies
    116
    Views
    126,866

    Have you tried the trans clean procedure? I...

    Have you tried the trans clean procedure? I wonder if your just not communicating with the TCM correctly.
  25. Replies
    116
    Views
    126,866

    Well it definitely should have worked in the...

    Well it definitely should have worked in the Camaro. I'll do some more digging. Camaro1 is a GM tech, he may have seen this before. With the trans temp too low, you will get the message "trans temp...
Results 1 to 25 of 204
Page 1 of 9 1 2 3 4