Search:

Type: Posts; User: efiv6

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    34
    Views
    17,094

    Read post # 27 and you will find the answer

    Read post # 27 and you will find the answer
  2. Replies
    13
    Views
    7,874

    I personally don't do nothing with my stft as...

    I personally don't do nothing with my stft as long as my ltft are as close to 0 as possible and my commanded afr and my actual afr are the same stft always moving to fast
  3. Replies
    13
    Views
    7,874

    Your math is correct most i found like 12.00 to...

    Your math is correct most i found like 12.00 to 12.20 log torque source and take her out and hammer it that will tell you what torque management source is kicking in
  4. Replies
    13
    Views
    7,874

    Yes 2000 on up in my car witch is the same yours...

    Yes 2000 on up in my car witch is the same yours but an auto. I my work good at .8550 but all cars are a little different. Don't forget stoich is 14.08
  5. Replies
    13
    Views
    7,874

    First off on theses cars when you reflash them...

    First off on theses cars when you reflash them you may have to drive them some 20 miles or so do to adptive learning. Two depending on what fuel is available in your area 91 or 93 is how much timming...
  6. Replies
    13
    Views
    7,874

    Check for air leaks at the cai connections I will...

    Check for air leaks at the cai connections I will look at your tune over the next couple of day and get back to you .
  7. Awesome!! Eric great work you are the best !!!!...

    Awesome!! Eric great work you are the best !!!!
    Thanks for all the hard work !!!!!
    Tony K.
  8. Eric Will this work on the ESYS 2048k for...

    Eric
    Will this work on the ESYS 2048k for the 3.7 V6 the same way calib.write only ????
    Thanks
    Tony
  9. Go to a site called master engine tuners look...

    Go to a site called master engine tuners look under project cars you will find a 3.7 v6 mustang they tuned with hp tuners read the article. I when't 13.7 with what Dan said and after a lot more...
  10. Thread: Transient fuel

    by efiv6
    Replies
    4
    Views
    3,221

    Thank you for your help that makes sences ,i will...

    Thank you for your help that makes sences ,i will be testing this so i will report back on how i make out. Thanks again for all you help
  11. Thread: Transient fuel

    by efiv6
    Replies
    4
    Views
    3,221

    Transient fuel

    Hi all,
    Can anybody tell me how the accel gain and time constant in transient fuel??? What does raising or lowering the numbers in the tables do ? Is it like a pump shot on a carb.
    thanks...
  12. Replies
    61
    Views
    34,175

    I also agree with wbt - as far as building a...

    I also agree with wbt - as far as building a street strip combo go sit in the stands at a nhra or ihra event watch stock elim. Run then go check them out. No magical parts just a good combination of...
  13. Replies
    34
    Views
    17,094

    Your welcome just takes a little looking with all...

    Your welcome just takes a little looking with all the hints i gave !!!!! I spent a lot of time on this thank god that part is over. I could not tell all as i do not make money doing this and most...
  14. Replies
    15
    Views
    17,562

    Ok to get you started : Fuel cut torque ratio (...

    Ok to get you started : Fuel cut torque ratio ( enter 0 in whatever cell you want to disable )
    Spark torque ratio limit ( enter 1.00 in whatever cell you want to...
  15. Replies
    34
    Views
    17,094

    Ok if you look under engine torque management ...

    Ok if you look under engine torque management there are three limiter tables fuel - fuel and spark - spark only there you will find the answer to the BOA 2000 rpm limiter
  16. Thread: 2.25 Scanner

    by efiv6
    Replies
    60
    Views
    35,303

    Nice that's great news ! Thanks for all the...

    Nice that's great news !
    Thanks for all the hard work Eric !
  17. Thread: 2.25 Scanner

    by efiv6
    Replies
    60
    Views
    35,303

    Eric, Did you try the 2.25 scanner out yet...

    Eric,
    Did you try the 2.25 scanner out yet ????
  18. Hi Mat, First off the V6 cars use a...

    Hi Mat,
    First off the V6 cars use a CHT ( cylinder head temp ) sensor ! there is no ECT sensor so it should be set to disable and the CHT set to enable !
  19. Replies
    34
    Views
    17,094

    Eric, I am working on getting a log for you . For...

    Eric, I am working on getting a log for you . For some reason i keep getting a Initalization error every time i try to log the Mustang with the 2.24 scaner
    Thanks
  20. Replies
    34
    Views
    17,094

    Thanks Sultan, I did that and it stills limiting...

    Thanks Sultan, I did that and it stills limiting rpm to 2000
    Thanks
  21. Replies
    34
    Views
    17,094

    Ok will do Thanks

    Ok will do
    Thanks
  22. Replies
    34
    Views
    17,094

    Eric, no this did not correct the issue still...

    Eric, no this did not correct the issue still limiting rpm to 2000
    Thanks
  23. Replies
    34
    Views
    17,094

    Eric did you find anything ????????? Thanks

    Eric did you find anything ?????????
    Thanks
  24. Replies
    34
    Views
    17,094

    [ATTACH]46902 Here is a copy of a stock 2014...

    [ATTACH]46902
    Here is a copy of a stock 2014 Mustang 3.7 V6 Auto. file
    Thanks
  25. Replies
    34
    Views
    17,094

    Thanks Russ I tried all that and it still limits...

    Thanks Russ I tried all that and it still limits RPM to 2000 when brake is applied !
    Eric, I will post a copy of my stock file for you in the morning
    Thanks
Results 1 to 25 of 39
Page 1 of 2 1 2