Search:

Type: Posts; User: mcdonald77

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    19
    Views
    2,350

    I did everything you listed 2006 TBSS and so far...

    I did everything you listed 2006 TBSS and so far my only issue is the indicator stays in P. The trans shifts and doesn't throw codes. Im having PCM of NC do remote tuning for me so I can change...
  2. Replies
    5
    Views
    1,751

    update, I made an excel spread sheet that...

    update, I made an excel spread sheet that coincides with the MAF Hz. After logging I wrote my wideband readings in a steady state compared to the average percent of difference. It got more in line...
  3. Replies
    5
    Views
    1,751

    91277 91278 91279 91276 91280 Here...

    91277 91278 91279 91276 91280

    Here is the tune, log and scanner charts, channels and graphs.
  4. Replies
    5
    Views
    1,751

    I'll get a log and post it.

    I'll get a log and post it.
  5. Replies
    5
    Views
    1,751

    It's an fbody so the intake is short, SLP lid...

    It's an fbody so the intake is short, SLP lid into the spectre 4" Maf housing. I installed a 3/4" honey comb mesh from saxonpc. Thats why I am wonder if people have clocked them a certain way on...
  6. Replies
    5
    Views
    1,751

    Idle tuning MAF not steady

    I am tuning an LS7 maf on a 6.0L with an ls3 top end. The car is a 98 firebird with a 411 ecu swap.

    My issue is tuning below 2875 Hz. Has anyone tuned the ls7 maf in an fbody? My other thought is...
  7. Replies
    0
    Views
    680

    opening compare file hangs

    As of the last few updates my compare files hang and won't load until I try it multiple times. Is there a fix?

    90849
  8. hptuners 3.0 VE and MAF tuning histogram question

    On the previous versions of hptuners my histo's displayed parentage of error in the form of ( .98, 1.02), Can I get 3.0 to display the same instead of -2.88 or 1.49. I know the info is the same but I...
  9. Replies
    2
    Views
    1,419

    lol, been using hptuners off and on for a few...

    lol, been using hptuners off and on for a few years. Never had to do that. Man do I feel stupid. Much appreciated!
  10. Replies
    2
    Views
    1,419

    VE TABLE reads 0 to 5%

    I was going to add more fuel to my lower rpm region and I dumb thumbed it. At the time there was a g/s indicator near were I enter the table multiplier. Now my VE is low percentages instead of whole...
  11. Replies
    30
    Views
    33,352

    I am still learning to use my scanner. I have...

    I am still learning to use my scanner. I have applied all the charts, graphs and channels. When I open the channels, the last one says unknown. Any tips to get it working. I did DL the maths

    72678
  12. Replies
    8
    Views
    6,579

    I got a lot of info from his book. The 12.5...

    I got a lot of info from his book. The 12.5 target is a safety so you don't start out lean. As soon and you have some confidence in what your doing, adjust accordingly. I used the 12.5 and quickly...
  13. Here is a pic of my old VE table with the 04 Z06...

    Here is a pic of my old VE table with the 04 Z06 cam. Even with those peaks and valleys, it drove great. I tried getting it smooth but it didn't seem to like the changes that round it all out. The...
  14. Its coming together nicely. I am working on the...

    Its coming together nicely. I am working on the upper rpm levels now. Its hard to hit the higher levels on the streets. I am up to 4000 rpm. I will compare my starting and ending VE tables then scale...
  15. I have not, Sorry. DSteck might, he posted in...

    I have not, Sorry. DSteck might, he posted in another thread about adding flex non flex vehicles. I have my pid's sorted out and all is good for tuning. I was multiplying wrong when applying changes...
  16. Ahh, now it's becoming more clear. Thank you.

    Ahh, now it's becoming more clear. Thank you.
  17. I had the AFX setup in Lambda before being...

    I had the AFX setup in Lambda before being upgraded to the afm1600L

    user.9004 is [PID.6001]/14.22222 PID.6001 is Air fuel ratio commanded hi res

    When I enter the above formula I get...
  18. I meant to quote this in my last post. I will...

    I meant to quote this in my last post. I will check all options given and report back. Might be a day or so but I will reply back.
  19. I really appreciate you guys that responded. I...

    I really appreciate you guys that responded. I will give this a try tonight or in the morning. If you guys need any pin outs or wire diagrams, let me know. I can also send you some 411 ecu terminals...
  20. I will double check on the speed density, my MAF...

    I will double check on the speed density, my MAF table is zeroed out. Today I will make sure to hit the reset fuel trims and turn them off. Im pretty sure I did.
  21. Lambda error PID ...

    Lambda error PID

    http://i1143.photobucket.com/albums/n633/jamcdonald/Lambda%20error%20PID_zpscntha5mc.jpg

    wide band PID ...
  22. percentage of error from lambda. The log is in...

    percentage of error from lambda. The log is in the original post, title is 07-07-15.hpl

    thanks for taking a look
  23. Feels like I am trying to hit a moving target. Logging VE error

    I installed a new came 224/230 595/595 112 LSA. I added 2 grams to base running airflow and used a VE table that seems to be more in line them my old one.

    When logging percent of error at cruise...
  24. where do we find Chris White? Im pretty sure the...

    where do we find Chris White? Im pretty sure the vette BCM's are flashed and locked by VIN so id love to find a way to get around this.
  25. I was doing some research on the corvette BCM and...

    I was doing some research on the corvette BCM and cluster. Pretty sure that even if its turned off in the BCM the cluster is still going to look for it and give a chime when not present. I was...
Results 1 to 25 of 56
Page 1 of 3 1 2 3