Search:

Type: Posts; User: Silspark

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    226

    It has camshaft and lock phaser

    It has camshaft and lock phaser
  2. Replies
    4
    Views
    226

    143927 143924

    143927
    143924
  3. Replies
    4
    Views
    226

    Throttle Limp mode

    Hellcat with Whipple 3.0 ( 100mm BBK throttle) going into limp mode with Throttle Sign in Dashboard in WOT or in normal acceleration but above 4000 RPM, the thing I observe is the (Throttle Torque...
  4. Replies
    1
    Views
    575

    Throttle Limp mode

    Hellcat with VMP 105 Throttle body has issue in high rpm with throttle sign after 6k rpm, after Dyno run the TPS Stuck in 15.7%





    128775
  5. Replies
    4
    Views
    1,358

    whats the parameter should I log to figure out...

    whats the parameter should I log to figure out the throttle closing

    some of torque management are happy in WOT so whats others could do that's closing
  6. Replies
    4
    Views
    1,358

    ATSv LF4 throttle issue

    Hi


    ATSv LF4 with bolts on, in the dyno also in rad test, there are throttle shuts in the middle of the RPM and open full in higher RPM

    Logs and file are attached

    116851
    116852
  7. Replies
    9
    Views
    3,584

    any ideas

    any ideas
  8. Replies
    7
    Views
    2,399

    u r Wlcm

    u r Wlcm
  9. Replies
    9
    Views
    3,584

    there no VVE in 2019+ so I was paying around...

    there no VVE in 2019+ so I was paying around Virtual Torque tables

    there are no Clean Throttle Process in the VCM

    I usually doing that in 2018 and below but in 2019+ not exiting

    regards
  10. Replies
    7
    Views
    2,399

    Try this file

    Try this file
  11. Replies
    9
    Views
    3,584

    I have modify MassTuning file and getting better...

    I have modify MassTuning file and getting better

    still the are little RPM fluctuating without AC but with AC is perfect

    also I have attached the stock file
  12. Replies
    9
    Views
    3,584

    I have reduced it in 500 RPM but no luck

    I have reduced it in 500 RPM but no luck
  13. Replies
    9
    Views
    3,584

    2019 Silvrado IDLE

    Hi

    new 2019 Silverado has single turbo upgrade only, the issue is in IDLE not stable and going into Negative timing
    I have adjust many table in torque management but no luck
    also I'm seeing...
  14. Replies
    7
    Views
    3,403

    So i have bring back the injector voltage to...

    So i have bring back the injector voltage to stock??

    Scale the injector half
    Double the stoich
    Cut the IVT half

    Thats it?
  15. Replies
    7
    Views
    3,403

    ID1300 scaling

    RPM are not stable after installing the ID1300 and put scaled data ( 63.5 are my limit).
    with scaling data I doubling the Voltage also I play with Torque EQ with same result , no leak no issues....
  16. Replies
    6
    Views
    2,199

    Its updates it properly as i always did in other...

    Its updates it properly as i always did in other cars but i didn't get the logic of droping between 3000-5000 rpm and then maintain the desired pressure till redline,
  17. Replies
    6
    Views
    2,199

    Low side are 65+ psi all the run

    Low side are 65+ psi all the run
  18. Replies
    6
    Views
    2,199

    416 with LT4 fueling Upgrade

    I have 416ci L86 with LT4 HPFP and injectors and LT4 camshaft , I have tune the injectors with LT4 table but the issue is there are drop in HPFP pressure between 3000 to 5000 RPM only and Injector DC...
  19. Replies
    1
    Views
    1,009

    C6 z06 Camshaft torque managment

    Hi

    I have Z06 2008 with stage IV camshaft 25x duration, I have issue with torque management timing reduction below 2K RPM , I have attached logs with file.
    right now there are driving hesitation ...
  20. Thread: Lt4 hpfp

    by Silspark
    Replies
    2
    Views
    1,477

    Lt4 hpfp

    We have installing LT4 HPFP and tune it but I found huge drop in mid range while the low side pressure are 55psi+

    416 with LT4 camshaft and HPFP
    twin turbo
  21. Replies
    2
    Views
    1,235

    Yes it's and also in highway with light throttle...

    Yes it's and also in highway with light throttle also
  22. Replies
    2
    Views
    1,235

    2016 hellcat whipple 4.5 swap

    Hi

    We have upgrade stock block hellcat with whipple 4.5 and whipple billet big bore throtle 2750, the issue is in idle is and light throttle but in WOT is fine.
    I undrestand whats happen due to...
  23. Replies
    5
    Views
    2,302

    I have reduce the airflow after meth upgrade (...

    I have reduce the airflow after meth upgrade ( Alky 2 nozzle), but not luck

    I have tried to play with camshaft timing and Injector timing but same result, in knock area Im getting little black...
  24. Replies
    5
    Views
    2,302

    is this problem are related with 2014 model only...

    is this problem are related with 2014 model only ???
  25. Replies
    5
    Views
    2,302

    5200+ Worried knock

    HI


    I have C7 14 with H/C with V3 supercharge, has unreasonable knock above RPM 5200, 5+ knock so I decide to add Alky to reduce the stress on injector but same result

    C7 14
    38% overlobe...
Results 1 to 25 of 76
Page 1 of 4 1 2 3 4