Search:

Type: Posts; User: Sherminator

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    8,961

    What are the recommended changes to perform in...

    What are the recommended changes to perform in the tune when running one of these? What are the improvements to be expected over a factory modular MAF?
  2. Make sure you have good flow and smooth plumbing...

    Make sure you have good flow and smooth plumbing for the intercooler system. If you have the lines going up and down to get around the rad/grill area it can effect the flow. Seen that a few times on...
  3. Replies
    5
    Views
    2,638

    No, uses a rubber grommet.

    No, uses a rubber grommet.
  4. Thread: 2010 zr1

    by Sherminator
    Replies
    4
    Views
    2,746

    You can do a ton of stuff before changing...

    You can do a ton of stuff before changing injectors let alone the pump.
  5. Thread: 2010 zr1

    by Sherminator
    Replies
    4
    Views
    2,746

    Good luck with acting out on your "reading"....

    Good luck with acting out on your "reading". Check out Lingenfelter as they've done lots of them and have parts waiting that work with proven results, I've installed tons of their stuff. Air intake,...
  6. Replies
    5
    Views
    2,638

    One from a 97-00 C5 will work. Get the pigtail as...

    One from a 97-00 C5 will work. Get the pigtail as well so you can wire it in nice.
  7. Installation can be from 9-3 o'clock with no...

    Installation can be from 9-3 o'clock with no issues. As close as possible to the factory sensors is best, and before the catalytic converters of course. You can use the factory locations, but you...
  8. Replies
    3
    Views
    2,808

    This means nothing. Just because your prior setup...

    This means nothing. Just because your prior setup was good, doesn't mean the tune was correct for the parts you had installed. His data for these injectors is very close if you were to install them...
  9. Replies
    7
    Views
    3,994

    What car are you using it on?

    What car are you using it on?
  10. Replies
    19
    Views
    32,985

    Di-electric grease used on the plug end of the...

    Di-electric grease used on the plug end of the wires? Fill the end of the boot up and click it back on. That has solved our issues on 95% of misfires we see on stock to mild engines.
  11. Replies
    3
    Views
    1,866

    Make sure fuel pressure is at 58psi and the...

    Make sure fuel pressure is at 58psi and the wideband sensor is warmed up and ready to read when you kick the key over. Wideband should be reading high 12's to 14's on the initial running to prevent...
  12. Replies
    10
    Views
    3,928

    Go to "Engine Diagnostics"-"General" and put your...

    Go to "Engine Diagnostics"-"General" and put your cursor on the P0121 items and read the bottom description and do what it says, see if that works for you.
    Also, the bog is probably because you are...
  13. Replies
    8
    Views
    3,682

    What does it have for a reluctor wheel, crank...

    What does it have for a reluctor wheel, crank sensor(color?) and cam gear(1X or 4X).
  14. Replies
    7
    Views
    3,566

    You can disable the DOD if that's what you want...

    You can disable the DOD if that's what you want to do.
  15. Should be 55-60psi. Ideally 58psi.

    Should be 55-60psi. Ideally 58psi.
  16. Replies
    12
    Views
    6,249

    Use the LS1 knock sensors and mount them to the...

    Use the LS1 knock sensors and mount them to the side of the block where the LS3 ones are...you will need to drill and tap the hole bigger for the LS1 style thread. Racetronix sells an extension...
  17. Replies
    7
    Views
    4,655

    A good flowing air intake will make both of those...

    A good flowing air intake will make both of those without requiring a tune. I recommend a sealed air box with a dryflow filter like a Volant, good flow, no oily air filter to deal with. Don't bother...
  18. Replies
    12
    Views
    6,249

    What does it use for a crank reluctor wheel and...

    What does it use for a crank reluctor wheel and cam pickup? Computer needs 24 tooth crank input and cam is 1X input. Engine is 58 tooth crank and 4X cam. Maybe you know this, just starting with basic...
  19. Replies
    12
    Views
    6,249

    Assuming you're using a LS1 block, does the LS3...

    Assuming you're using a LS1 block, does the LS3 cam have the cam pickup on it? There is a few things that would cause issues with this setup; the above concern, wrong injector data, bad MAF data from...
  20. Replies
    6
    Views
    3,718

    Do what we suggested and see what happens.

    Do what we suggested and see what happens.
  21. Replies
    6
    Views
    3,718

    Very true!

    Very true!
  22. Replies
    6
    Views
    3,718

    What is the mileage on the car? Any odd sounds...

    What is the mileage on the car? Any odd sounds from the engine? To determine false or actual knock, cut the timing down by a sufficient amount like 10 degrees in the suspect areas, confirm good...
  23. Replies
    39
    Views
    21,956

    Or just run injectors that you can properly...

    Or just run injectors that you can properly calibrate for. A 60lb injector is good for what like 800-900hp or more at 58psi. You have is a stock 5.3 with 10psi looking at your sig. can't see that...
  24. Replies
    3
    Views
    2,724

    Do you have the right cam and crank sensor setup?...

    Do you have the right cam and crank sensor setup? You need to either swap the crank reluctor wheel to 24 tooth or use a signal conversion box. The cam needs a 1X cam gear with the right adapter...
  25. Replies
    8
    Views
    3,935

    Fix the white smoke first. What are the outside...

    Fix the white smoke first. What are the outside air temps when running the car? It's not just cold weather exhaust condensation is it?
Results 1 to 25 of 111
Page 1 of 5 1 2 3 4