Search:

Type: Posts; User: EDH

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,870

    Thanks a ton for that. Already loaded it up and...

    Thanks a ton for that. Already loaded it up and it worked. They had a regular relay on the fan but the noise just killed the character of the car. I wired up a dodge pwm module and at 50% you barely...
  2. Replies
    2
    Views
    1,870

    e67 PWM fan control not working in tune.

    I have a 1962 Corvette with 2012 zl1 motor package. Using an e67 pcm with operating system 12628912. I have also installed a pwm fan controller. The fan speeds work correctly when controlling them...
  3. HELP. Am I screwed....E67 OS for stand alone mode

    I have attempted to contact HPTuners with no results. I have a LS9/4l80 combo in stand alone mode. Transmission is on its own controller. I am running an e67 pcm with the 12628912 operating system....
  4. SMEC , thanks for the reply. It has a 4l80e with...

    SMEC , thanks for the reply. It has a 4l80e with stand alone trans controller. There is no clutch pedal to relearn. I wonder if there is a work around.
  5. GHuggins, I could spend $100 in credits to find...

    GHuggins, I could spend $100 in credits to find out but would love if HPTuners support could tell me if that was necessary.
  6. barum, thanks for the reply. I have all 3 of...

    barum, thanks for the reply. I have all 3 of those set to "no error reported" and still have no luck. The errors come back every time.
  7. Help needed. 62 Corvette with LS9. No start issue..New combo

    We have a 62 Corvette here with no start issue. Data logging shows no injector pulse width ever. Not sure I have disabled all the theft and safety tables properly. Attached is the tune, log file and...
  8. Thanks for the info. I thought it was a low side...

    Thanks for the info. I thought it was a low side output. Will give the other a try. Thanks for the help.
  9. LS1swap ECU fuel pump control not working, 04 GTO pcm

    I have an IS300 with ls1 swap from an 04 GTO. The issue I am having is the fuel pump control in the pcm does not seem to work. It will not prime at key on. Wont kick in when motor is running and does...
  10. Replies
    2
    Views
    1,736

    Found this after Russ K told me I was missing...

    Found this after Russ K told me I was missing some tables.
    http://www.hptuners.com/forum/showthread.php?54793-TCC-duty-cycle-table
  11. Replies
    14
    Views
    5,214

    Thanks Russ, I will do that.

    Thanks Russ, I will do that.
  12. Replies
    2
    Views
    1,736

    Help with 98 4l80e convertor lockup

    I have a 96 chevy truck with a 98 7.4L and 4l80e swap. Everything works fine with the swap with the exception of converter lockup. With a stock trans tune (speedo and calculated speed untouched) the...
  13. Replies
    14
    Views
    5,214

    Here is the tune and some logs. I lowered the tcc...

    Here is the tune and some logs. I lowered the tcc apply/release table significantly and now I have an issue where the converter will rapidly lock and unlock at certain loads.
  14. Replies
    14
    Views
    5,214

    16241014 for the seventh segment. Thanks

    16241014 for the seventh segment. Thanks
  15. Replies
    14
    Views
    5,214

    I wouldn't think so unless a 7.4L came with a...

    I wouldn't think so unless a 7.4L came with a 4l60 at one point. It also up/down shifts perfectly.
  16. Replies
    14
    Views
    5,214

    Correct, it never locks. But if it did, I would...

    Correct, it never locks. But if it did, I would like to have converter lock on light decel.
  17. Replies
    14
    Views
    5,214

    I tried it with the brake input connected and...

    I tried it with the brake input connected and disconnected with no difference. The calculated speed input is correct. We have ran the vin on the pcm and it also showed it was a 7.4L 4L80e vehicle....
  18. Replies
    14
    Views
    5,214

    Thanks Jon S. I have been able to read it and...

    Thanks Jon S. I have been able to read it and tune it. The issue is nothing will make the convertor lock up except applying ground to the tcc wire at the pcm. I get a momentary "apply en" but never...
  19. Replies
    14
    Views
    5,214

    Is 9365095 a OS setup for the 4L80E

    I have a 96 chevy truck with a 7.4l and 4l80 swap. The ECU serv# is 16250279 and the operating system is 9365095. It appears to shift all gears fine but will not lock the converter under any...
  20. Replies
    0
    Views
    989

    98 big block getting p0102 at key on

    I have a 98 Chevy truck that we just swapped a big block into. It is throwing code p0102 at key on/motor not running. Once I crank it and clear the DTC, it is gone until I force it to stall. I have...
  21. I Had The Same Issue And Was Able To Get A Log By...

    I Had The Same Issue And Was Able To Get A Log By Putting A Battery Charger On The Fuse Box. Why Does My Phone Cap The First Letter Of Every Word.....
  22. Replies
    7
    Views
    3,231

    Throttle stop under gas pedal.....

    Throttle stop under gas pedal.....
  23. Replies
    21
    Views
    7,686

    Many times you are able to do a read but HPT will...

    Many times you are able to do a read but HPT will not allow you to license the pcm to load a new tune on it. LS Edit does the same thing to us with HPT.
  24. Replies
    21
    Views
    7,686

    This.....

    This.....
  25. Replies
    21
    Views
    7,686

    You stated that you were not able to do a flash...

    You stated that you were not able to do a flash to the original ecu. I assume you were able to do a read?
Results 1 to 25 of 55
Page 1 of 3 1 2 3