Search:

Type: Posts; User: dbb2797

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    17
    Views
    5,939

    Awesome, thanks CCS86, adjusting the WOT...

    Awesome, thanks CCS86, adjusting the WOT start/end is now getting me the results I expect with the throttle closing.
    blackbolt22, take a look at he below log too. I had the throttle angle channels...
  2. Replies
    17
    Views
    5,939

    I updated with a third log that's accurate. The...

    I updated with a third log that's accurate. The air temp is actually within a few degrees. I've seen a number of times the ambient not being logged correctly and it always defaults to that 59 when...
  3. Replies
    17
    Views
    5,939

    ahhh I totally missed that post from you but I...

    ahhh I totally missed that post from you but I see it now. Thanks! I'm going to go try upping the WOT end in a few minutes. I'll report back with the results.
  4. Replies
    17
    Views
    5,939

    That is correct. I am 100% confident that the...

    That is correct. I am 100% confident that the only thing different between the runs is DD table. In fact to make sure when I changed the DD that I was working on the same exact tune I had previously...
  5. Replies
    17
    Views
    5,939

    here is a log with the ambient accurate and...

    here is a log with the ambient accurate and within a few degrees for comparison. As you can see, same thing. The torque values are much higher (about 150 higher) than my tune where I purposefully set...
  6. Replies
    17
    Views
    5,939

    that is literally the only difference in those...

    that is literally the only difference in those two logs. It is just the DD. The tune is the only difference. Yes I've noticed that every once in a while the ambient temperature is not accurate in...
  7. Replies
    17
    Views
    5,939

    But how would you change the functionality in the...

    But how would you change the functionality in the tune to follow indicated torque at WOT?

    Also this is what doesn't make sense to me. The ECU is using the driver demand table to command a certain...
  8. Replies
    17
    Views
    5,939

    driver demand at wot

    I've been doing experimentation trying to understand how the torque model and driver demand works while in WOT. I purposely set the driver demand torque quite low at WOT. I see the indicated torque...
  9. Replies
    7
    Views
    2,253

    Adding more fuel will do the opposite of what I'm...

    Adding more fuel will do the opposite of what I'm trying to achieve though. More fuel will equal higher swings in performance when the car heat sinks and then cools off in a matter of minutes. I need...
  10. Replies
    7
    Views
    2,253

    Ahh right I should have mentioned this is the...

    Ahh right I should have mentioned this is the coyote and it's NA. Specifically in my case it's in a 2011 Mustang. 31* is perfectly safe at .857 with E85. I have probably close to a thousand WOT trips...
  11. Replies
    7
    Views
    2,253

    How lean do you think you can go with E85?

    Not for maximum performance per say, but this is more for consistency at the track. Something I've noticed with my car is that when it gets really heat soaked, it will drop .03-.04. But all it takes...
  12. Replies
    72
    Views
    36,049

    really good point and description. With my newly...

    really good point and description. With my newly stalled converter I have a lot more adjustability for RT. So even if the relays are a few hundredths slower (which it sounds like they most likely...
  13. Replies
    72
    Views
    36,049

    found the relays tonight at autozone and wired it...

    found the relays tonight at autozone and wired it up and it looks to be working great with very limited testing in my garage. I wired up the 2 relay initially and may test the 3 relay in the near...
  14. Replies
    72
    Views
    36,049

    Awesome thanks!

    Awesome thanks!
  15. Replies
    72
    Views
    36,049

    Found the schematics in this thread with good...

    Found the schematics in this thread with good info. Now I just need to hunt down the relays. ...
  16. Replies
    72
    Views
    36,049

    Can somebody point me to the parts list and...

    Can somebody point me to the parts list and schematics needed for the 2 and 3 relay transbrakes? I have a 2011 GT and I ran the JMS for most of last year. It randomly failed at the end of last...
  17. Replies
    3
    Views
    2,240

    The intake only cams are designed to work across...

    The intake only cams are designed to work across the entire VCT range. So no limiters are needed. My instinct tells me that since these cams have more duration, that in the middle and high RPM ranges...
  18. Replies
    3
    Views
    2,240

    L&M Intake Cams 2011 Mustang

    Has anybody tuned the intake cam events against the L&M Intake cams? I'm going to be purchasing them in a few weeks and bracket tuning them. I don't believe I need to do anything special beyond the...
  19. Replies
    15
    Views
    5,776

    It looks look like you may be getting tipin right...

    It looks look like you may be getting tipin right at the launch too. I see the timing drop right off at the launch and your spark source goes to tipin. Could you also log torque source?
  20. Replies
    1
    Views
    3,356

    giving this a bump because I plan on updating to...

    giving this a bump because I plan on updating to these cams over the winter too.Does anybody know what the true limit is?
  21. Replies
    72
    Views
    36,049

    Thanks wbt. I've raised the pressure a little...

    Thanks wbt. I've raised the pressure a little bit. Also I had the clutch fill time at 1-2 at .20. I've seen recommendations for the shorter clutch fill times by others , but I think that is the wrong...
  22. Replies
    72
    Views
    36,049

    8 launches at the track today with no limp mode...

    8 launches at the track today with no limp mode issues at all. It was very consistent launching too. All my 60fts were within .01 of each other.

    My only issue now is a 1-2 transmission slip...
  23. Replies
    72
    Views
    36,049

    That makes sense. Your RT's were consistent which...

    That makes sense. Your RT's were consistent which pointed to it not being related to the launch. When I spin too, it generally doesn't affect RT.
  24. Replies
    72
    Views
    36,049

    I did some testing tonight with about 4 hits off...

    I did some testing tonight with about 4 hits off the JMS transbrake with good luck and no codes or limp mode. The last time I had it installed I don't even think I got 2 launches without it throwing...
  25. Replies
    72
    Views
    36,049

    I installed the JMSChip Launch Max transbrake...

    I installed the JMSChip Launch Max transbrake today. I've had it sitting around but reinstalled it today. I also have a 3600 stall Circle D. wbt, what RPM have you been launching at? I'm thinking of...
Results 1 to 25 of 148
Page 1 of 6 1 2 3 4