Search:

Type: Posts; User: Spectre

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    3,960

    I'm not sure what the PID.2811 is..are you going...

    I'm not sure what the PID.2811 is..are you going through the EGR? But my PID is basically the same = Volts/0.7143+9.
    The custom PID does the same as the default NGK PID. I have my ground and...
  2. Replies
    3
    Views
    2,190

    Haha, oh ok. I didn't notice it was you! I just...

    Haha, oh ok. I didn't notice it was you! I just knew there was a thread about it since my car does basically the same thing. I have LG Pro headers too.
  3. Replies
    8
    Views
    3,960

    I tried a custom PID and it was the same. I have...

    I tried a custom PID and it was the same. I have my black power wires ground ed to my chassis and my analog grounded to my EIO. Should I ground the analog to the same location instead of the EIO? ...
  4. Replies
    8
    Views
    3,960

    NGK maxing at 15.73

    I hooked up my NGK wideband and noticed the max it will read in the scanner is 15.73-15.75. The NGK LCD gauge will read 16.0 max (range is supposed to be 9-16). Though it does read 9I can't look at...
  5. Replies
    3
    Views
    2,190

    I think someone had a similar problem here: ...

    I think someone had a similar problem here:

    http://www.hptuners.com/forum/showthread.php?t=19185
  6. Replies
    100
    Views
    34,175

    Oh yeah, I forgot. I rewired mine to be separate.

    Oh yeah, I forgot. I rewired mine to be separate.
  7. Replies
    100
    Views
    34,175

    What if you have turned on in the tune but...

    What if you have turned on in the tune but unplugged, or unplug it while it's misfiring...?
  8. Replies
    48
    Views
    46,253

    You still using these values RWTD?

    You still using these values RWTD?
  9. Replies
    5
    Views
    3,033

    Speaking of IGNV...what does that mean? Is it...

    Speaking of IGNV...what does that mean? Is it the same as the vs VAC table? Or does it work differently.
  10. Replies
    98
    Views
    112,192

    Haha, hey chris. I have my stock injectors in...

    Haha, hey chris. I have my stock injectors in now until I figure out how to tune the SD 60lbers. I'm assuming it doesn't use the volts vs map table the way its setup from the factory b/c it's...
  11. Replies
    98
    Views
    112,192

    How would you edit Offset vs Press vs IGNV? I'm...

    How would you edit Offset vs Press vs IGNV? I'm not even sure I understand what that table means? My 08 C6 also has a Offset vs Volts vs Map...but it's all zero'd out. I'm confused.
  12. Replies
    1
    Views
    2,175

    KB boost a pump

    I have a question about tuning for the use of a boost a pump. My BAP is hooked to a hobbs switch to come on during boost only. If anyone has ever used a BAP they know it has a dial to adjust the...
  13. Replies
    10
    Views
    5,629

    Did you try reprogramming the LC1 to see if the...

    Did you try reprogramming the LC1 to see if the a/f value it was showing changed. Here's a good thread on how to check for voltage offsets.

    http://www.hptuners.com/forum/showthread.php?t=11018...
  14. Thread: what wideband

    by Spectre
    Replies
    5
    Views
    2,814

    I use the NGK afx with upgraded sensor (Ntk...

    I use the NGK afx with upgraded sensor (Ntk sensor).
    I had an LC-1 and it was a total pain in the ass. The LC-1 can be a good unit, but it's super picky and i think they have a lot of bad units...
  15. Replies
    10
    Views
    5,629

    It may have reset how you have the voltage...

    It may have reset how you have the voltage settings set up...the custom inputs? eg. Like 0v = 10 a/f and 5v =18 a/f or are you using the ones already input into hp tuners?
  16. Replies
    6
    Views
    3,427

    Maybe try adding a little more to the Min idle...

    Maybe try adding a little more to the Min idle airflow table in the lower RPM range. If you add too much you'll know...the idle will probably hang and not come down. I'm fighting the same type...
  17. Replies
    6
    Views
    3,282

    Did you change injectors or anything besides the...

    Did you change injectors or anything besides the cam?
  18. Replies
    317
    Views
    244,401

    Did you use the stock coast down spark table?

    Did you use the stock coast down spark table?
  19. Replies
    6
    Views
    5,763

    Here's a good thread by 5_liter_eater you may...

    Here's a good thread by 5_liter_eater you may want to read:

    http://www.hptuners.com/forum/showthread.php?t=15564
  20. Replies
    1
    Views
    2,414

    Car Dies After Letting off clutch

    Ok, first off I'm new at this so be patient if I sound like a complete idiot. My history...I just finished up installing a procharger on my 2008 C6 (E38). I also installed an ECS blower cam as well...
  21. Replies
    48
    Views
    46,253

    Ok, I've finally got my car together and sat down...

    Ok, I've finally got my car together and sat down to work on my tune for these 60 lb injectors. I'm going to try and use the data you posted (post #120) as my starting point. I'm a little lost when...
  22. Replies
    6
    Views
    4,676

    I thought it was best just to leave the A/c...

    I thought it was best just to leave the A/c torque table alone.
  23. Replies
    2
    Views
    1,923

    Ah, ok thanks! His car will start will try to...

    Ah, ok thanks! His car will start will try to start and just die. His fuel pump doesn't prime when the key is turned to the on position, if it does, the car will start and run...at least for a...
  24. Replies
    2
    Views
    1,923

    VCM scanner 02 z06

    A buddy of mine is having trouble with his car starting up. He's got an 02 z06 and it won't start. We've tried almost everything we can think of and can't figure out what's wrong with it. I had a...
  25. Replies
    48
    Views
    46,253

    Would the values be the same for the shorty...

    Would the values be the same for the shorty injectors? The part # is 107962 I believe. They're supposed to be rated the same...
Results 1 to 25 of 55
Page 1 of 3 1 2 3