Search:

Type: Posts; User: mtcrusan

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,902

    Thanks Bill!

    Thanks Bill!
  2. Replies
    2
    Views
    1,902

    Microsoft .NET

    Will the suite work with the latest Microsoft .NET?
  3. Replies
    19
    Views
    19,586

    Take the gear ratio that is in your PCM and...

    Take the gear ratio that is in your PCM and divide it by the drive sprocket ratio which equals your FDR. Mine is a stock 04 MC so my Calculated gear = 3.29 / Drive Sprocket Ratio = 1.121 equals your...
  4. Replies
    5
    Views
    2,705

    Air Intake or Air Charge Temperatures!

    Hello,
    Is there a way to scan for the air going into the motor after the supercharger on W bodies? I looked and cannot find the PID. I know the V8 guys have this option.
  5. Replies
    3
    Views
    2,884

    I calibrated the WB with voltage offsets, but I...

    I calibrated the WB with voltage offsets, but I scanned for Raw Voltage last night and I'm seeing 1.323 - 1.328 V with AFR reading 16.XX. It might be a grounding issue. I am goning to go through it...
  6. Replies
    3
    Views
    2,884

    Wideband (LC-1) issues!

    I have a LC-1 WB and I recalibrated it yesterday as per Soud Engineer's instructions. I had the WB for awhile now and it seems that it never worked correctly. What I am seeing is during cruise I am...
  7. Replies
    5
    Views
    2,527

    :cheers:

    :cheers:
  8. Replies
    47
    Views
    30,088

    I have an 04 L67 and the Injector Flow Rate vs....

    I have an 04 L67 and the Injector Flow Rate vs. KPA VAC only goes up to 100 kPa. Mine is sloped.
  9. Thread: error

    by mtcrusan
    Replies
    5
    Views
    2,695

    It shows here you are using 2.1.16.0. Maybe try...

    It shows here you are using 2.1.16.0. Maybe try uninstalling it completely and installing it fresh. HTH!
  10. Thanks Eddie. I will try it out.

    Thanks Eddie. I will try it out.
  11. Replies
    25
    Views
    9,748

    This happens on my 03 Trailblazer also....

    This happens on my 03 Trailblazer also. Intermittently.
  12. Attached are my stock timing tables. What do you...

    Attached are my stock timing tables. What do you think I could bump my timing up to? I see knock in the higher RPM's, but nothing during cruising. Would it be safe to increase timing by 5 degrees at...
  13. Replies
    27
    Views
    10,446

    What are your IPW's? I think they max out at 21ms.

    What are your IPW's? I think they max out at 21ms.
  14. Replies
    47
    Views
    30,088

    So your saying 18.055%? 100% = 1

    So your saying 18.055%?

    100% = 1
  15. Thread: LS1 MAF table

    by mtcrusan
    Replies
    3
    Views
    3,221

    There is a lot here! MAF Tables...

    There is a lot here! MAF Tables
  16. Replies
    8
    Views
    4,209

    I think the table is under Engine > Fuel Control...

    I think the table is under Engine > Fuel Control > General > Injector Control > Flow Rate vs. KPA
  17. Replies
    10
    Views
    4,397

    Post the current tune also.

    Post the current tune also.
  18. Replies
    179
    Views
    159,511

    I have been fighting with tuning the fueling at...

    I have been fighting with tuning the fueling at part throttle for a while. I have a WB installed permanently (LC-1). I thought I was good in OL, but when I switched back to CL my trims are rich and...
  19. Replies
    179
    Views
    159,511

    I was running a 3.4" and I jumped to a 3.6"...

    I was running a 3.4" and I jumped to a 3.6" recently.
  20. Replies
    4
    Views
    4,519

    225 multiplied by 0.50 (aspect ratio = 50) times...

    225 multiplied by 0.50 (aspect ratio = 50) times 2 (2 side walls) divided by 25.4 (to convert mm into inches) plus 16 (wheel diameter) equals 24.85826 inches.
  21. Replies
    179
    Views
    159,511

    I put some 100 octane in my car and my knock went...

    I put some 100 octane in my car and my knock went away. I will order a larger pulley and re gap the plugs to 0.040 and see. I will post logs soon.
  22. Replies
    19
    Views
    10,033

    I know of a vendor who sells a false knock retard...

    I know of a vendor who sells a false knock retard kit. It is some Dynomat for the transaxle and knock sensors.

    Russ, In your tuning experience is there a relationship with knock in certain areas...
  23. Replies
    179
    Views
    159,511

    Yes I am. I get a spike during the transient...

    Yes I am. I get a spike during the transient stage. I want to make it close, but now it seems to overshoot either way most times. I appreciate the help.
  24. Replies
    179
    Views
    159,511

    Also I am going to get some 100 octane gas to see...

    Also I am going to get some 100 octane gas to see if the KR is real or not.
  25. Replies
    179
    Views
    159,511

    How close should the WOT MAF table be? I have one...

    How close should the WOT MAF table be? I have one area in the transient stage that spikes lean. Then I correct it and the next run it spikes fat. TIA!
Results 1 to 25 of 206
Page 1 of 9 1 2 3 4