Specifically, I get "time out at loc 0" when I try to read entire. '08 balt SS.
Type: Posts; User: 05HD
Specifically, I get "time out at loc 0" when I try to read entire. '08 balt SS.
Is this the same for SS/TC? I haven't updated my software in ages but it still works fine on all of the old junk I tune. Just can't connect to this '08 balt to fix the blow up tune some hack put in...
That is disappointing. I guess I will be doing more standalones for the FI stuff.
Bill, I see this post is from 2007.
Is there any plans to fix this permanently with access to the correct table? The IFR workaround is a rather annoying bodge IMO.
May as well check myself in on the truck thead as well. I have an '05 Silverado LS 4x4/2500HD/ECSB/6.0 . I got the HP to tune a TT GTO I put together for a friend and it has been permanetly attached...
Haha. Im talking about the traction control spark retard vs. rpm and agressive retard vs. rpm tables in the torque management general section.
It was snowing the day I zeroed the tables out. I...
My 05 K25 was a burnoutless wonder too. Then I found the hidden traction control with the HP and I can now leave senseless clouds of rubber John Force would be proud of when powerbraking it. It still...
Gives intermittent errors with Vista basic on my Dell Latitude. Sometimes requires a reboot or unplug/replug of the usb. Annoying sitting on a dyno paying by the hour...
Any luck with this?
^ Ding! They mix it with gas so you can't drink it. :chug: :cheers: :chug:
Was fine before changing injectors? Only thing changed was injectors? Probably a bad injector if yes to both...
So, you've taken some timing out and it still does it?
Maybe carboned up considering the mileage. Try some top engine cleaner?
On the GTO I did recently, similar symptoms were due to min PW bieng too long for the new injectors. One time it would be just right @ minimum pulse, then another it would be super pig rich. Fuel...
The best way to do it is on the dyno. You are looking for MBT or the minimum timing for best torque. Advance until torque doesn't go up or has a minimal increase for every load and RPM point. Be...
How do you have the analog outputs configured on the LC-1? They can be customized...
No, he either doesn't know or is lying. They are different.
Oh, ok. What was he referring to not working without the MAF then? :shrug:
Apparently not when you convert to SD?
You want to install the resistor on the 12v power line to the injector. The best way to do it (IMO) is to pick one or two of them out of one of the many imports that came with OEM injector resistors,...
LMAO! Acceleration Slip Regulation. It pushes the gas pedal back at your foot if you step on it too hard.
Pupshot gets flushed with SD? Is this true for LS2 (E40) as well? Any way to recoup it or compensate without going back to MAF? I was wondering why the GTO I'm tuning feels soggy and goes lean on tip...
Knew I forgot something! I left the P0068 diagnostis active, lol. I was saying "WTF is safety mode" as I coasted to the side of the road, dead in the water...
I did decide to make seperate...
I was also wondering if it would be considered safe to tune the high octane spark table for 100 octane and leave the low octane one a bit consevative for 93 so all that would be needed is filling the...
Cool, thanks for the help EC_Tune.
Anyone else have an opinion to share? :secret:
You guys trying to weasel your way around getting your warranty voided are the ones that always wind up getting the big void stamp. Bieng up front and honest with the person fixing your car still...