Search:

Type: Posts; User: Witt

Page 1 of 16 1 2 3 4

Search: Search took 0.00 seconds.

  1. Pretty much.

    Pretty much.
  2. All I did was disable bank 2 s1. Your LTFT vs...

    All I did was disable bank 2 s1. Your LTFT vs bank and heaters were already setup. I didn't shut off any associated DTCs.
  3. Replies
    4
    Views
    959

    You can create a filter in the graph layout to...

    You can create a filter in the graph layout to only log when above a percentage of that designated mapped point.
  4. Fuel Base and Fuel Base Cold under Fuel -> Open...

    Fuel Base and Fuel Base Cold under Fuel -> Open Loop tab
  5. Replies
    2
    Views
    1,035

    Try [ECM] 44799, ETC Torque Max vs RPM. It's used...

    Try [ECM] 44799, ETC Torque Max vs RPM. It's used in park neutral.
  6. Took a quick glance, your desired load doesn't go...

    Took a quick glance, your desired load doesn't go above 1.0 possibly because you have map max delta above baro pressure set to 0 under your speed density tab. Could be the PCM trying to limit the...
  7. Copperhead has it set to .2 from the factory cal....

    Copperhead has it set to .2 from the factory cal.

    I can without a problem. I either have to populate the TIP max table, hack the ETC PR table, or remap the TB with huge values. Since populating...
  8. I do have desired airmass disabled. It will FMEM...

    I do have desired airmass disabled. It will FMEM the TB without any indication in VCM Scanner.

    I'm curious as to what ecoboost strategies have as a tp pressure ratio filter constant.

    I have 6...
  9. Since I've used that max tip table that you found...

    Since I've used that max tip table that you found and populated it correctly via SCT, I don't have to do this hardly at all, as my TB model doesn't blow up in boost.

    I create a histogram with the...
  10. Replies
    2
    Views
    770

    If you zero out the manifold vacuum multiplier,...

    If you zero out the manifold vacuum multiplier, you can keep the injector data as returnless, no need to set the pressure multipliers to 1 and calculate the flow rate for a set pressure. You do have...
  11. You don't have to scale it, lol. It's fine....

    You don't have to scale it, lol. It's fine. That's the reporting limit of the PID.
  12. Replies
    22
    Views
    9,233

    335 https://easyupload.io/vvdsxx

    335

    https://easyupload.io/vvdsxx
  13. Replies
    96
    Views
    75,635

    Without seeing a log, I would take a guess at...

    Without seeing a log, I would take a guess at maybe driver demand torque being a bit too low on the bottom row.
  14. Replies
    96
    Views
    75,635

    I also have a turbo equipped switch, turned that...

    I also have a turbo equipped switch, turned that on thinking that would enable the Max Tip table. It just caused a wrench light and a maf circuit code and instantly died, but the max tip table seems...
  15. Replies
    96
    Views
    75,635

    I just populated this table on my turbo...

    I just populated this table on my turbo copperhead and it seems to be working exactly like you said. I went back to the stock TB model and i have no more than +- 1 degree of throttle correction.
  16. Replies
    56
    Views
    11,356

    I'm not convinced that's the issue since the...

    I'm not convinced that's the issue since the inferred ethanol is actually changing. I lean towards the stability threshold being too narrow or your air meter (MAF or MAP) not being accurate enough...
  17. Replies
    5
    Views
    2,762

    I'm pretty sure even setting that to a high max...

    I'm pretty sure even setting that to a high max load won't do it as even stock values should be at an airload threshold that's under idle. Thinking something like an ECT vs time parameter. A log of a...
  18. Replies
    5
    Views
    2,762

    I agree and I don't think that will work because...

    I agree and I don't think that will work because the trick is to keep idle in emissions reduction and the only frpp strat that does is the boss with the red key.
  19. Replies
    5
    Views
    2,762

    Distance tables aren't obeyed at idle with torque...

    Distance tables aren't obeyed at idle with torque based decel disabled unless in emissions reduction mode, which is the mode Ford uses on the Boss red key cals to have a lopey idle and dashpot...
  20. Replies
    5
    Views
    1,343

    Take a trust but verify approach here, but this...

    Take a trust but verify approach here, but this is what I found...

    First of all, you can't disable fuel cut, period, unless you disable torque limiting totally, which Steven mention in a linked...
  21. Thread: MAF Maxxed Out?

    by Witt
    Replies
    10
    Views
    2,315

    Lift pump isn't keeping up. Fuel system went into...

    Lift pump isn't keeping up. Fuel system went into FMEM.
  22. Replies
    25
    Views
    5,280

    Its torque control according to your log. Disable...

    Its torque control according to your log. Disable shuffle switch and relog.
  23. I use a buck converter wired to the SJB.

    I use a buck converter wired to the SJB.
  24. N2MB box causes issues with this test unless that...

    N2MB box causes issues with this test unless that parameter is changed.

    107718
  25. 2019 F150 TC-277, just grabbed the first 10r80...

    2019 F150 TC-277, just grabbed the first 10r80 file I had.
Results 1 to 25 of 386
Page 1 of 16 1 2 3 4