Search:

Type: Posts; User: Turbofox

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    4,304

    Does anything seem off with the Cam timing? Or...

    Does anything seem off with the Cam timing? Or do the values that are in there seem to make sense? They should still be the stock truck settings. Which I would think would be ok. Unless with...
  2. Will do, i'll see if they can make them available...

    Will do, i'll see if they can make them available for me! I think thats the most confusing part. It's hard sometimes to know what could be there or what should be there when it's not available.
  3. 06 F-150 Transient Fueling, Rich Off Throttle.

    Hey Guys, After installing the new 60 LB/Hr injectors i'm starting to get a rich off throttle condition for a second or two. So I'm assuming that's the transient fueling. Trims are all +-3% so...
  4. Replies
    10
    Views
    4,304

    I'll give that a shot as well!

    I'll give that a shot as well!
  5. Replies
    10
    Views
    4,304

    I did notice they were disabled. So I re-enabled...

    I did notice they were disabled. So I re-enabled them last night. I didn't see any settings for them other than on/off though.
  6. Replies
    10
    Views
    4,304

    Yup, were actually thinking that the truck has...

    Yup, were actually thinking that the truck has clogged Cats. I did flatten out the MAF curve after the dyno, we kept tossing fuel at it to try and see if it would change but it was really starting...
  7. Replies
    10
    Views
    4,304

    06 F-150, 230HP at 15PSI! Any suggestions?

    Hey guys, finally got my F-150 on the Dyno tonight. Truck drives great, but as soon as you get into boost it pretty much falls on it's face. Makes about the same or less power then a stock F-150. ...
  8. Replies
    162
    Views
    124,978

    Yup, already gave that a shot. Ended up going...

    Yup, already gave that a shot. Ended up going back to 2.24 for the time being to at least get the fuel stuff sorted out a bit more.
  9. Replies
    162
    Views
    124,978

    Any updates on if this computer will be supported...

    Any updates on if this computer will be supported in the new scanner?
  10. Replies
    23
    Views
    29,414

    Finally got a chance to try out the new scanner...

    Finally got a chance to try out the new scanner and see if I could get this throttle stuff figured out. Looks like hardly anything will log yet on this ECU i'm assuming :(...
  11. Replies
    162
    Views
    124,978

    Hey Eric, just got to test the scanner out on my...

    Hey Eric, just got to test the scanner out on my 2006 F-150 (ECU Black Oak 1472K). Are the PID's etc all done with this ECU yet? I can't read O2 other then voltage and a bunch of other things I was...
  12. Replies
    23
    Views
    29,414

    Yup that’s pretty much what we had figured. And...

    Yup that’s pretty much what we had figured. And I definitely am planning on setting this back down to stock or close to stock once the ETC stuff has been tuned. A lot of the issues were that HP...
  13. Well, I gave it a try with both the min and both...

    Well, I gave it a try with both the min and both bank tables with no change to the offset. So I'm assuming that I can't change it at all anywhere :(
  14. Replies
    2
    Views
    2,806

    Not a problem i'll shoot an e-mail off. Going to...

    Not a problem i'll shoot an e-mail off. Going to do some tuning now so if it comes back again i'll also grab a screen shot as well.
  15. Replies
    2
    Views
    2,806

    Failed Write, Negative Response Code 7X

    I've been starting to get these more and more frequent when trying to load the tune into my 06 F-150. I used to get them once in a blue moon but it seems to be 1/3 times I load or even more. Whats...
  16. Everything looks good on the hardware side of...

    Everything looks good on the hardware side of things. Both banks are swinging voltages etc like I would think they should.
    I think it's just the Biasing. What setting would this be changed...
  17. Will do Eric. I'm going to look over my tunes as...

    Will do Eric. I'm going to look over my tunes as well to make sure it didn't get switched by accident anywhere. Just didn't want to change something that shouldn't be tinkered with. I'll double...
  18. 06 F-150, Changing base Commanded o2 (should be 14.6 actually is 15.0)

    Hey guys, I’m still tinkering on the truck. And I know that the fuel base table only commands open loop fueling. However when it’s in closed loop the truck seems to command closer to 15.0-15.1...
  19. Replies
    19
    Views
    10,684

    OOOOOOO awesome! Maybe i'll just try a few more...

    OOOOOOO awesome! Maybe i'll just try a few more things later this week and limp it along a bit till it comes out then. (I drive the truck every day so it gets annoying lol)
  20. Replies
    3
    Views
    2,878

    I'd love to see how you guys have the throttle...

    I'd love to see how you guys have the throttle body setup! I'm having a lot of issues with my 06 with a vortech blower now. Otherwise yes, HP tuners works good! Just be ready for the 3 min+...
  21. Replies
    19
    Views
    10,684

    Not a problem Eric I know you guys have been...

    Not a problem Eric I know you guys have been working on it. Is there any tips on at least trying to “guess” to make it better. I’ve just put on a Vortech blower, so now everything is super...
  22. Replies
    19
    Views
    10,684

    Can the TQ table parameters be logged yet or will...

    Can the TQ table parameters be logged yet or will that be out with the newest version of the scanner? Or is there a way to figure them out at least?
  23. Replies
    23
    Views
    29,414

    I would agree with you on it not being the best. ...

    I would agree with you on it not being the best. However it's pretty hard to "tune" something when it hit's limp mode the instant you step on the throttle... So, if you get the error, before you...
  24. Replies
    23
    Views
    29,414

    I'll have to give it a shot then sometime this...

    I'll have to give it a shot then sometime this week. Still getting the dashpot stuff corrected as well but i'm getting closer. But the throttle stuff is starting to really bug me, even when the...
  25. Replies
    23
    Views
    29,414

    I definitely agree! It just seems like at the...

    I definitely agree! It just seems like at the moment a lot of the parameters aren’t available to us to log or calibrate. A write up would be awesome Eric!
Results 1 to 25 of 54
Page 1 of 3 1 2 3