Is is possible to run a 6L80E transmission with a E40 and a T42?
Type: Posts; User: Rat Chevelle
Is is possible to run a 6L80E transmission with a E40 and a T42?
No, I am not.
I set the transmission to manual, and I do not even have a VSS, thats why I tried to switch on calibration from VSS to RPM, but the ETC kept failing like that.
Granted it returned to...
Hello,
We are using a 2.2 Ecotec out of a 2007 Malibu on an off road buggy, the issue is that the RPM does not climb down fast enough when you let off the pedal, they linger for a second or two at...
I broke the light speed today...
I went 698+ million miles, and the light speed is "only" 670+ million, so I beat it by a safe margin.
To achieve that I had to spin the engine to nearly 113...
Well, it turns out I had a lot of pressure from the guy. He had killed the ecu trying to install a superchips (or so he says) so I could not think straight.
I was getting at it from the quick menu,...
Hi,
I´ve got an issue with a 2000 Vette.
It had a fried ECU when I got here, somebody had already installed a 2000 Tahoe ECU, they both have the same serv no. 09354896.
I opened the Tahoe ECU...
I have also done several ECMs with th350s and 400s and no VSS with no problem. As a matter of fact I did an S10 with a 6.0 and a th350 like the one from this post, the guy has run 11.06 and drives it...
I live in Hermosillo, Sonora, Mexico.
Two and a half hours drive from the Arizona border for those geographically challenged ;)
And it is HOT in here, we´ve been 44 celsius in October, poor IAT...
I finally got it!
I stepped away for a bit, took a shower, came back and voila!
I guess you gotta scroll down DUH!
Amazing what a cool head can accomplish.
Thanks to all, because although I got...
I just switched to a 2.5 bar COS on a Gen IV truck, and I can not get the MAP to read on the gauges, I can not get the STFT's or LTFT's to show on the histograms.
They do show on the table, but I...
Has anyone used the dual sync distributor to control a "411" PCM?
The reason is that I would love to have the Gen III programability for diferent brand engines and FAST makes dual sync's for many...
Hello,
Is there a way to adapt and connect a Gen III Electronic pedal onto a GenIV?
By looking at the schematics they both have two potentiomenters, what I do not know is the values and resistances...
Am I even posting in the right site?
Thanks, it is conforting to see someone care...
Yes I am a member and I just posted it over there, thanks.
Hope someone replies quick-
I need some light on the segment swap for the 06 Chevy...
Please...
Thanks
I urgently need to solve the DBW issue explained above.
I am attaching the files for both the 03 Escalade that is not responding to the pedal, and the 06 Chevy which responds to the pedal but has a...
Hello,
I need to swap the transmission segments to convert over from a 4L80E to a 4L60E.
Thea reason for this swap is that I couldnt make the ETC work with the original ECM and tried differents...
I was told on LS1Tech that the TAC and pedal have to match the ECM, is there a way to relink what I already have, or how do I know where the TAC came from so that I can refglash that OS onto the ECM?...
Hello, I am having a DBW issue...
I installed an ECM and harness from an 03 Escalade onto a Rockcrawler Jeep, the original ETC pedal and TAC did not work, I used another Pedal and TAC and it worked...
53 Mercury, I have pm´d you with my email, but in case you miss it it is [email protected].
Thanks a lot, I am looking forward to hearing from you.
L Corbala
Yes, and that center plug is the one I need to know how to connect, as I said before I need the outputs for the fuel pump, speedo, tach, DLC, check engine light, electronic pedal connectors, power,...
BUMP
I wanna hear about this one, as I have the same problem too in my 4.8 powered 69 C10!
1998Ws6 is correct.
That is a 2 valve E-Van series from 2006, I am attaching a picture of the vehicle's info from where I pulled it.
If you have any other questions please let me know, all I need...
Hi I said I was going to post pictures of the ECM so you could see them, here they are.
Hope this is the one you have info for.
If you need any aditional data please let me know.
Thanks a lot....
Yes, I only intend to modify the original harness.
I plan on removina all emission related stuff like rear o2's and egr and so on, I will delete these from the DTC's list.
And yes, I have the three...