Page 66 of 832 FirstFirst ... 165662636465666768697076116166566 ... LastLast
Threads 1301 to 1320 of 16626

Forum: GM V8 Tuning - Engine, Gas (Gen 4)

(2005-2015, LS2, LS7, ...)

  1. Sticky Thread Sticky: Read Me!!! Tuning How-To's & General Information

    Started by Bill@HPTuners, 01-06-2007
    3 Pages •
    1 2 3
    3 Attachment(s)
    • Replies: 40
    • Views: 247,009
    TheMechanic
    06-06-2023 Go to last post

  1. Need help w injector data for early E38 with 12609749 injectors

    Started by Alexslo1k, 01-31-2023
    2 Attachment(s)
    • Replies: 2
    • Views: 651
    Alexslo1k
    02-01-2023 Go to last post

  2. Driveability Tune Attached

    Started by grubinski, 08-11-2022
    2 Attachment(s)
    • Replies: 8
    • Views: 2,436
    grubinski
    01-31-2023 Go to last post

  3. New FIC 1700CC Injectors - No Start

    Started by nitrousgp, 01-29-2023
    2 Attachment(s)
    • Replies: 15
    • Views: 1,788
    nitrousgp
    01-31-2023 Go to last post

  4. Question Hanging rpm/idle, new manifold and throttle body

    Started by Sean1m, 01-31-2023
    • Replies: 5
    • Views: 1,134
    Alvin
    01-31-2023 Go to last post

  5. Ramp in rate/PE delay for Truck Norris cam only Silverado?

    Started by JLawson240, 01-30-2023
    • Replies: 2
    • Views: 697
    Tunercharged
    01-31-2023 Go to last post

  6. a different injector scaling question - using Injector Flow Multi vs MAP - ECM 33390

    Started by NotSure, 01-31-2023
    2 Attachment(s)
    • Replies: 3
    • Views: 657
    Alvin
    01-31-2023 Go to last post

  7. speed odometer correction

    Started by morepowerjoe, 01-27-2023
    • Replies: 14
    • Views: 1,833
    morepowerjoe
    01-30-2023 Go to last post

  8. How to get rid of negative timing during warm up

    Started by JASON11WS6, 04-03-2021
    • Replies: 7
    • Views: 1,751
    peter logan
    01-29-2023 Go to last post

  9. Btr truck cam

    Started by PAYDAMAN, 01-25-2023
    5 Attachment(s)
    • Replies: 3
    • Views: 1,281
    Bgramling524
    01-28-2023 Go to last post

  10. freezing cold start

    Started by marksrig, 12-23-2022
    3 Pages •
    1 2 3
    22 Attachment(s)
    • Replies: 44
    • Views: 4,533
    marksrig
    01-28-2023 Go to last post

  11. e40 gto closing throttle on start?

    Started by mxguy1286, 01-28-2023
    2 Attachment(s)
    • Replies: 1
    • Views: 466
    eXo3901
    01-28-2023 Go to last post

  12. 6.2L swap Ls3 Check my Scan please ???????

    Started by isaacace09, 01-27-2023
    2 Attachment(s)
    • Replies: 8
    • Views: 1,425
    TheMechanic
    01-28-2023 Go to last post

  13. Torque converter recommendations

    Started by CammedUp, 01-23-2023
    • Replies: 7
    • Views: 1,236
    RDF1
    01-26-2023 Go to last post

  14. Idle LTFT just not consistent >

    Started by Turbo6TA, 01-26-2023
    • Replies: 1
    • Views: 436
    GHuggins
    01-26-2023 Go to last post

  15. E38 and Scaling for ID1000's

    Started by HawkZ28, 09-28-2022
    1 Attachment(s)
    • Replies: 15
    • Views: 2,393
    UMSTuning
    01-26-2023 Go to last post

  16. would appreciate some insight from a professional on my tune.

    Started by Ata77068, 01-22-2023
    5 Attachment(s)
    • Replies: 14
    • Views: 1,628
    Ata77068
    01-25-2023 Go to last post

  17. 06 E40 Idle surges up down Timing Stays at 0 Degrees

    Started by ybotlq4btr3, 01-25-2023
    2 Attachment(s)
    • Replies: 2
    • Views: 618
    ybotlq4btr3
    01-25-2023 Go to last post

  18. Stand alone harness/E38 question

    Started by Lakegoat, 01-23-2023
    • Replies: 4
    • Views: 862
    Lakegoat
    01-25-2023 Go to last post

  19. high rev when shifting t56 magnum

    Started by LS ROB, 12-05-2021
    2 Attachment(s)
    • Replies: 2
    • Views: 869
    LS ROB
    01-25-2023 Go to last post

  20. Can not figure out random Lean conditions

    Started by bcutler21, 01-25-2023
    3 Attachment(s)
    • Replies: 2
    • Views: 491
    bcutler21
    01-25-2023 Go to last post
Page 66 of 832 FirstFirst ... 165662636465666768697076116166566 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.