Page 448 of 831 FirstFirst ... 348398438444445446447448449450451452458498548 ... LastLast
Threads 8941 to 8960 of 16610

Forum: GM V8 Tuning - Engine, Gas (Gen 4)

(2005-2015, LS2, LS7, ...)

  1. Sticky Thread Sticky: Read Me!!! Tuning How-To's & General Information

    Started by Bill@HPTuners, 01-06-2007
    3 Pages •
    1 2 3
    3 Attachment(s)
    • Replies: 40
    • Views: 242,825
    TheMechanic
    06-06-2023 Go to last post

  1. MAF calibration vs. IAT temps

    Started by erick_e, 09-22-2015
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 24
    • Views: 11,565
    eficalibrator
    10-07-2015 Go to last post

  2. Base tune for new setup

    Started by EFI, 10-07-2015
    • Replies: 0
    • Views: 908
    EFI
    10-07-2015 Go to last post

  3. VE Tuning an Auto TBSS

    Started by rio95, 10-05-2015
    • Replies: 3
    • Views: 2,217
    Eaglegoat
    10-07-2015 Go to last post

  4. spare e38 ecu

    Started by goat perf, 10-06-2015
    1 Attachment(s)
    • Replies: 1
    • Views: 1,184
    thesubfloor
    10-06-2015 Go to last post

  5. Is this a case of needing the e38 Manifold Vacuum Patch?

    Started by granatl, 09-27-2015
    2 Pages •
    1 2
    4 Attachment(s)
    • Replies: 23
    • Views: 10,252
    Nate007
    10-06-2015 Go to last post

  6. ID1300 Injectors, Short Pulse Adder Table-Will Not accept injector data. Please Help!

    Started by DRTWRK, 10-05-2015
    • Replies: 6
    • Views: 3,372
    ElecTech
    10-06-2015 Go to last post

  7. 2008 6.0 Van

    Started by MikeOD, 07-07-2015
    • Replies: 6
    • Views: 4,098
    Rocko350
    10-05-2015 Go to last post

  8. p2138 code with truck or Monte pedal

    Started by bigseth, 09-20-2015
    • Replies: 1
    • Views: 1,856
    Rocko350
    10-05-2015 Go to last post

  9. 11 Ls3 and 02 4L60e loss of power issue

    Started by cpd004, 10-04-2015
    3 Attachment(s)
    • Replies: 0
    • Views: 820
    cpd004
    10-04-2015 Go to last post

  10. E38 Injector Timing on 2010 Camaro

    Started by GeeForceJunkie, 10-03-2015
    • Replies: 3
    • Views: 2,276
    schpenxel
    10-03-2015 Go to last post

  11. advance tq. management is killing me. can anybody look at my logs and help?

    Started by 06blackgto, 10-03-2015
    5 Attachment(s)
    • Replies: 10
    • Views: 3,806
    schpenxel
    10-03-2015 Go to last post

  12. cutoff with backfire

    Started by 7amood, 10-14-2012
    • Replies: 4
    • Views: 3,627
    alisahloul37
    10-03-2015 Go to last post

  13. Fluttering Throttle Body ???

    Started by seven ends, 09-28-2015
    1 Attachment(s)
    • Replies: 3
    • Views: 3,484
    schpenxel
    10-02-2015 Go to last post

  14. Transient Fuel - Warmup vs. Impact Factor

    Started by Aaron407, 09-23-2015
    • Replies: 9
    • Views: 5,648
    Aaron407
    10-02-2015 Go to last post

  15. Confused... STFT's are negative... but WB sensor shows super lean!

    Started by RealQuick, 09-28-2015
    4 Attachment(s)
    • Replies: 11
    • Views: 4,658
    schpenxel
    10-02-2015 Go to last post

  16. bucking after cam swap

    Started by will15, 09-28-2015
    5 Attachment(s)
    • Replies: 14
    • Views: 5,770
    will15
    10-01-2015 Go to last post

  17. VSS output settings

    Started by 1972C10_LS, 10-01-2015
    1 Attachment(s)
    • Replies: 0
    • Views: 1,228
    1972C10_LS
    10-01-2015 Go to last post

  18. Power Enrich settings

    Started by 1972C10_LS, 10-01-2015
    1 Attachment(s)
    • Replies: 2
    • Views: 1,330
    1972C10_LS
    10-01-2015 Go to last post

  19. cant populate histo's 3 and 4 ??

    Started by 2NDSLPSS, 09-28-2015
    2 Pages •
    1 2
    8 Attachment(s)
    • Replies: 25
    • Views: 8,234
    schpenxel
    10-01-2015 Go to last post

  20. New to HP Tuners - Running Rich & Very Sluggish/Hesitant takeoff

    Started by 1972C10_LS, 09-28-2015
    3 Attachment(s)
    • Replies: 11
    • Views: 4,017
    1972C10_LS
    09-30-2015 Go to last post
Page 448 of 831 FirstFirst ... 348398438444445446447448449450451452458498548 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.