Page 358 of 830 FirstFirst ... 258308348354355356357358359360361362368408458 ... LastLast
Threads 7141 to 7160 of 16595

Forum: GM V8 Tuning - Engine, Gas (Gen 4)

(2005-2015, LS2, LS7, ...)

  1. Sticky Thread Sticky: Read Me!!! Tuning How-To's & General Information

    Started by Bill@HPTuners, 01-06-2007
    3 Pages •
    1 2 3
    3 Attachment(s)
    • Replies: 40
    • Views: 240,805
    TheMechanic
    06-06-2023 Go to last post

  1. Injector upgrade for the LS3

    Started by RRRocketMan, 04-19-2017
    • Replies: 10
    • Views: 17,119
    RRRocketMan
    05-01-2017 Go to last post

  2. L92 E38 swap hard starting

    Started by XSKIER, 04-30-2017
    4 Attachment(s)
    • Replies: 16
    • Views: 5,101
    XSKIER
    05-01-2017 Go to last post

  3. Boost Enrich not changing commanded EQ

    Started by NJ_Phil, 04-30-2017
    2 Attachment(s)
    • Replies: 4
    • Views: 1,957
    LSxpwrdZ
    05-01-2017 Go to last post

  4. Engine torque management question (table definitions)

    Started by Niemer, 04-30-2017
    1 Attachment(s)
    • Replies: 0
    • Views: 735
    Niemer
    04-30-2017 Go to last post

  5. Can we discuss transients.... response time etc.

    Started by BigDaddyCool, 04-29-2017
    • Replies: 0
    • Views: 725
    BigDaddyCool
    04-29-2017 Go to last post

  6. Timing table resolution scaling for ID2000 05 Vette

    Started by FastBlackTA, 04-28-2017
    • Replies: 1
    • Views: 1,275
    mcfarlnd
    04-29-2017 Go to last post

  7. tip in lean spike

    Started by russ472, 04-29-2017
    1 Attachment(s)
    • Replies: 0
    • Views: 770
    russ472
    04-29-2017 Go to last post

  8. Take a look at these scans

    Started by Jonblarc7, 04-28-2017
    3 Attachment(s)
    • Replies: 4
    • Views: 1,470
    Jonblarc7
    04-28-2017 Go to last post

  9. MAF stack on 9000hz @ wot

    Started by steve-0, 04-27-2017
    1 Attachment(s)
    • Replies: 4
    • Views: 1,875
    steve-0
    04-28-2017 Go to last post

  10. Will be buying HPT soon, Camaro ZL1 bad tuner.....

    Started by Vicster, 12-03-2015
    7 Pages •
    1 2 3 ... 7
    49 Attachment(s)
    • Replies: 134
    • Views: 47,452
    Vicster
    04-28-2017 Go to last post

  11. loading a 2.24 config into 3.4

    Started by h2.4, 04-28-2017
    • Replies: 0
    • Views: 578
    h2.4
    04-28-2017 Go to last post

  12. Help with a CTSv

    Started by RawRacing, 04-25-2017
    2 Attachment(s)
    • Replies: 2
    • Views: 1,427
    RawRacing
    04-28-2017 Go to last post

  13. Holden HSV GTSR W1 - Stock Tune Anyone?

    Started by BigDaddyCool, 04-27-2017
    • Replies: 0
    • Views: 743
    BigDaddyCool
    04-27-2017 Go to last post

  14. DBC throttle body?

    Started by mrtony, 04-27-2017
    • Replies: 2
    • Views: 1,373
    mrtony
    04-27-2017 Go to last post

  15. Expected gains from a 5.3 2014 Silverado Z71

    Started by MADWHIP, 04-26-2017
    2 Attachment(s)
    • Replies: 3
    • Views: 1,498
    MADWHIP
    04-27-2017 Go to last post

  16. Question on Copying Injector Data - Offset vs. Press vs. IGNV Different

    Started by lxcoupe, 04-26-2017
    2 Attachment(s)
    • Replies: 2
    • Views: 1,517
    mowton
    04-27-2017 Go to last post

  17. Flex fuel idle gets richer as temp increases

    Started by Lakegoat, 04-25-2017
    2 Attachment(s)
    • Replies: 3
    • Views: 1,540
    Lakegoat
    04-27-2017 Go to last post

  18. Can't seem to get rid of surging idle issue - VVE tuning

    Started by adunphy, 01-16-2017
    3 Attachment(s)
    • Replies: 12
    • Views: 7,469
    adunphy
    04-27-2017 Go to last post

  19. Problems with 6l80 on a 2010 sierra.

    Started by 02Ls1, 04-26-2017
    1 Attachment(s)
    • Replies: 7
    • Views: 2,598
    02Ls1
    04-27-2017 Go to last post

  20. Basic question, would a 1x cam gear even fire on a 58x motor?

    Started by lxcoupe, 04-26-2017
    • Replies: 2
    • Views: 1,192
    lxcoupe
    04-26-2017 Go to last post
Page 358 of 830 FirstFirst ... 258308348354355356357358359360361362368408458 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.