Page 120 of 831 FirstFirst ... 2070110116117118119120121122123124130170220620 ... LastLast
Threads 2381 to 2400 of 16614

Forum: GM V8 Tuning - Engine, Gas (Gen 4)

(2005-2015, LS2, LS7, ...)

  1. Sticky Thread Sticky: Read Me!!! Tuning How-To's & General Information

    Started by Bill@HPTuners, 01-06-2007
    3 Pages •
    1 2 3
    3 Attachment(s)
    • Replies: 40
    • Views: 244,716
    TheMechanic
    06-06-2023 Go to last post

  1. C6LS3 cammed vette dies while ac is on

    Started by corvettemac, 11-16-2021
    3 Attachment(s)
    • Replies: 5
    • Views: 1,033
    corvettemac
    11-17-2021 Go to last post

  2. Negative numbers for the INJ. TIP TEMP OFFSET table?

    Started by marksrig, 11-16-2021
    • Replies: 5
    • Views: 1,077
    hjtrbo
    11-17-2021 Go to last post

  3. No injector data, after rebuild with cam same fuel injectors.

    Started by zshawnz, 10-20-2021
    4 Attachment(s)
    • Replies: 7
    • Views: 1,417
    zshawnz
    11-16-2021 Go to last post

  4. LS3 Syclone with 4l65e ECM Stuck in 4WD LOW Help

    Started by speedjunction, 11-15-2021
    4 Attachment(s)
    • Replies: 9
    • Views: 1,425
    blindsquirrel
    11-16-2021 Go to last post

  5. 2012 CTS-V with cam, pulley headers, etc. Need more startup "flare"

    Started by Snowman1987, 10-19-2021
    3 Attachment(s)
    • Replies: 10
    • Views: 2,325
    Snowman1987
    11-16-2021 Go to last post

  6. Knock in boost 3k-4k

    Started by ShartyMcQueef, 11-14-2021
    3 Attachment(s)
    • Replies: 3
    • Views: 987
    hjtrbo
    11-14-2021 Go to last post

  7. 2015 2500hd 6.0 help

    Started by blownjeep, 11-13-2021
    • Replies: 1
    • Views: 677
    5FDP
    11-13-2021 Go to last post

  8. cant speed density tune after cam install

    Started by Z107, 11-11-2021
    2 Attachment(s)
    • Replies: 2
    • Views: 1,082
    Lakegoat
    11-12-2021 Go to last post

  9. engine dies on startup only when hot after tsp bald eagle cam install

    Started by Z107, 11-09-2021
    2 Attachment(s)
    • Replies: 5
    • Views: 1,281
    Z107
    11-11-2021 Go to last post

  10. Tune review - New Cam and Torque Converter

    Started by danmw2003, 11-10-2021
    • Replies: 2
    • Views: 800
    danmw2003
    11-11-2021 Go to last post

  11. 2010 zr1 - vve spikes and lugging motor at low rpm

    Started by wassat, 10-13-2021
    14 Attachment(s)
    • Replies: 13
    • Views: 2,678
    wassat
    11-11-2021 Go to last post

  12. 11 silverado e38 bosch 210s starting and idle issue after scaling

    Started by [email protected], 11-05-2021
    2 Attachment(s)
    • Replies: 3
    • Views: 1,098
    [email protected]
    11-11-2021 Go to last post

  13. Need C6 2010+ ECM set up

    Started by AJ_in_Slapout, 11-06-2021
    • Replies: 3
    • Views: 869
    AJ_in_Slapout
    11-11-2021 Go to last post

  14. AFR chenge After fans works

    Started by Rayan_V8, 11-10-2021
    1 Attachment(s)
    • Replies: 0
    • Views: 516
    Rayan_V8
    11-10-2021 Go to last post

  15. LS376/480 Original ECM File

    Started by DBPE, 11-09-2021
    • Replies: 0
    • Views: 524
    DBPE
    11-09-2021 Go to last post

  16. Virtual Torque

    Started by wildfan1976, 11-06-2021
    1 Attachment(s)
    • Replies: 7
    • Views: 1,952
    wildfan1976
    11-09-2021 Go to last post

  17. E38 software with 4WD

    Started by skjeep, 10-25-2021
    2 Pages •
    1 2
    4 Attachment(s)
    • Replies: 24
    • Views: 6,012
    skjeep
    11-07-2021 Go to last post

  18. E38 T43 OS Compatibility

    Started by DSoutlaw, 11-06-2021
    1 Attachment(s)
    • Replies: 2
    • Views: 1,344
    DSoutlaw
    11-07-2021 Go to last post

  19. New cold start issue

    Started by chipflyer, 11-06-2021
    2 Attachment(s)
    • Replies: 2
    • Views: 856
    kevin87turbot
    11-07-2021 Go to last post

  20. vehicle speed not working until about 12-13 mph

    Started by idleor8, 11-07-2021
    2 Attachment(s)
    • Replies: 0
    • Views: 519
    idleor8
    11-07-2021 Go to last post
Page 120 of 831 FirstFirst ... 2070110116117118119120121122123124130170220620 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.